I cannot seem to find a topic in the Help file for migrating my custom label
files over to 2006 from the Labels folder in 2005. If I simply move them
from one directory to the other, I assume they will no longer be in 2005.
How to "copy" them from 05 to 06? And just the .lbl, .lbp and .lbw files, or
also the .~lbl?
George W1EBI
From [EMAIL PROTECTED] Fri May 6 16:18:53 2005
From: [EMAIL PROTECTED] (JNMazzoni)
Date: Fri May 6 16:26:47 2005
Subject: [Dxbase] Rotor Interface Problem / Hy Gain DCU-1 Continued
Message-ID: <[EMAIL PROTECTED]>
Still having problems .... cannot control the Hy Gain DCU 1 from Dxbase.
1. I have checked the Activate ROTOR 1 in the Rotor 1 tab
2. I have entered my QTH +44.89 Lat / +93.11Lon in USER opt/ General tab
3. I continue to get an error message as follows
The beam heading cannot be found.
Make sure the beam heading is present in the summary window.
If using arrow buttons make sure DX base has already set the current beam
heading.
I was advised that ;
First make sure that you have it 'enabled' in the correct rotor 1 page3 on the
User
Options.
Second, the first time you use DXB, you must tell it where the antenna is.
I do not understand the second instruction. Do I type in an arbitrary Log & Lat
?
Can someone give more specific detail on this set up. It seem like it should be
simple but I haven't had any luck.
Thank you
From [EMAIL PROTECTED] Fri May 6 16:30:50 2005
From: [EMAIL PROTECTED] (FireBrick)
Date: Fri May 6 16:38:21 2005
Subject: [Dxbase] Rotor Interface Problem / Hy Gain DCU-1 Continued
References: <[EMAIL PROTECTED]>
Message-ID: <[EMAIL PROTECTED]>
I'm assuming it's on a com port.
Could there be a comport conflict?
And it works with some other program?
I don't actually have the Hy-Gain DCU, I have the Idiom Press unit.
And the only time I get that message is if I've just started DXB and click on a
cluster
spot.
Sorry my suggestions didn't help.
----- Original Message -----
From: "JNMazzoni" <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Friday, May 06, 2005 3:18 PM
Subject: [Dxbase] Rotor Interface Problem / Hy Gain DCU-1 Continued
Still having problems .... cannot control the Hy Gain DCU 1 from Dxbase.
1. I have checked the Activate ROTOR 1 in the Rotor 1 tab
2. I have entered my QTH +44.89 Lat / +93.11Lon in USER opt/ General tab
3. I continue to get an error message as follows
The beam heading cannot be found.
Make sure the beam heading is present in the summary window.
If using arrow buttons make sure DX base has already set the current beam
heading.
I was advised that ;
First make sure that you have it 'enabled' in the correct rotor 1 page3 on the
User
Options.
Second, the first time you use DXB, you must tell it where the antenna is.
I do not understand the second instruction. Do I type in an arbitrary Log & Lat
?
Can someone give more specific detail on this set up. It seem like it should be
simple but
I haven't had any luck.
Thank you
______________________________________________________________
Dxbase mailing list
Home: http://mailman.qth.net/mailman/listinfo/dxbase
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
