Rich, Did you be sure to put a QSL # into each of those QSO's that have multiple QSO's on one QSL card??
73 Joe wa6axe Richard Detweiler wrote: > Hi, Jack, > > Thanks for the reply, I did run the DXCC module, however, It didn't > put my multible qso cards at the end... > > I am running the module for DXCC, > > Have selected all the cards I need for the DXCC award by marking DXCC in > Select, > > Run the wizard checking the select and DXCCputting the records in the > report table. > > Then run the DXCC award module selecting cards only and wizard records. > > I did select all the QSO's on the multiple QSO Cards > > so far, still only puts one qso on the report for multiple QSO Cards and > orders it as if is a single qso card. > > I've done something wrong, Any ideas? > > Best wishes. > rich > K5SF > >> From: "Jack" <[EMAIL PROTECTED]> >> To: "Richard Detweiler" <[EMAIL PROTECTED]>,<[email protected]> >> Subject: Re: [Dxbase] ModifiedDxccqso.rpt >> Date: Wed, 18 May 2005 11:16:39 -0400 >> >> Rich, >> >> The logic for this was enhanced in DXbase 2006 so that this report is >> no longer required. The logic in 2006 now sorts exactly as the ARRL >> specifies it should. Just run the DXCC awards module and that's it. >> >> Jack >> >> ----- Original Message ----- From: "Richard Detweiler" >> <[EMAIL PROTECTED]> >> To: <[email protected]> >> Sent: Wednesday, May 18, 2005 10:50 AM >> Subject: [Dxbase] ModifiedDxccqso.rpt >> >> >>> Where can I find the "ModifiedDxccqso.rpt" from Joe WA6AXE. >>> >>> And do I need it for DXCC? I have several cards that have multiple >>> entries, >>> >>> Would like them to sort to the end as it should. >>> >>> btw the reflector is bouncing all my messages today.. >>> >>> >>> best wishes, >>> Rich >>> K5SF >>> >>> >>> ______________________________________________________________ >>> Dxbase mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/dxbase >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:[email protected] >>> >> > > > ______________________________________________________________ > Dxbase mailing list > Home: http://mailman.qth.net/mailman/listinfo/dxbase > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > From [EMAIL PROTECTED] Wed May 18 12:01:25 2005 From: [EMAIL PROTECTED] (Joseph Glockner) Date: Wed May 18 12:10:45 2005 Subject: [Dxbase] ModifiedDxccqso.rpt In-Reply-To: <[EMAIL PROTECTED]> References: <[EMAIL PROTECTED]> <[EMAIL PROTECTED]> Message-ID: <[EMAIL PROTECTED]> The Field has a MAX size of 10 in the 2006 version .. shud be able to handle any variation of QSL # the user might come up with.. 73 Joe wa6axe Ron Stordahl wrote: > You need to read the help documentation under: > > Awards>DXCC>Multiple QSO's..... > > In order to get this feature to work you have to tell DXBase that a > given card contains multiple Q's. This is done by assigning a card > number to such cards. The suggestion is that you use something > consistent like the date (plus a serial number since you are likely to > receive many cards in a single mailing from the bureau for example). I > have not looked into how big the field can be, so this needs some > thought to get it right. > > Ron, N5IN > > Richard Detweiler wrote: > >> Hi, Jack, >> >> Thanks for the reply, I did run the DXCC module, however, It didn't >> put my multible qso cards at the end... >> >> I am running the module for DXCC, >> >> Have selected all the cards I need for the DXCC award by marking DXCC >> in Select, >> >> Run the wizard checking the select and DXCCputting the records in the >> report table. >> >> Then run the DXCC award module selecting cards only and wizard records. >> >> I did select all the QSO's on the multiple QSO Cards >> >> so far, still only puts one qso on the report for multiple QSO Cards >> and orders it as if is a single qso card. >> >> I've done something wrong, Any ideas? >> >> Best wishes. >> rich >> K5SF >> >>> From: "Jack" <[EMAIL PROTECTED]> >>> To: "Richard Detweiler" <[EMAIL PROTECTED]>,<[email protected]> >>> Subject: Re: [Dxbase] ModifiedDxccqso.rpt >>> Date: Wed, 18 May 2005 11:16:39 -0400 >>> >>> Rich, >>> >>> The logic for this was enhanced in DXbase 2006 so that this report is >>> no longer required. The logic in 2006 now sorts exactly as the ARRL >>> specifies it should. Just run the DXCC awards module and that's it. >>> >>> Jack >>> >>> ----- Original Message ----- From: "Richard Detweiler" >>> <[EMAIL PROTECTED]> >>> To: <[email protected]> >>> Sent: Wednesday, May 18, 2005 10:50 AM >>> Subject: [Dxbase] ModifiedDxccqso.rpt >>> >>> >>>> Where can I find the "ModifiedDxccqso.rpt" from Joe WA6AXE. >>>> >>>> And do I need it for DXCC? I have several cards that have multiple >>>> entries, >>>> >>>> Would like them to sort to the end as it should. >>>> >>>> btw the reflector is bouncing all my messages today.. >>>> >>>> >>>> best wishes, >>>> Rich >>>> K5SF >>>> >>>> >>>> ______________________________________________________________ >>>> Dxbase mailing list >>>> Home: http://mailman.qth.net/mailman/listinfo/dxbase >>>> Help: http://mailman.qth.net/mmfaq.htm >>>> Post: mailto:[email protected] >>>> >>> >> >> >> ______________________________________________________________ >> Dxbase mailing list >> Home: http://mailman.qth.net/mailman/listinfo/dxbase >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] > > > ______________________________________________________________ > Dxbase mailing list > Home: http://mailman.qth.net/mailman/listinfo/dxbase > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > From [EMAIL PROTECTED] Wed May 18 21:27:59 2005 From: [EMAIL PROTECTED] (John W. Benedict) Date: Wed May 18 21:37:23 2005 Subject: [Dxbase] Searching BBS Archives Message-ID: <[EMAIL PROTECTED]> Hello DXBase Group Is there a way to search this BBS archives? John
