Good list of thinks to work on, thanks! 73 Neal Campbell Abroham Neal Software www.dxbase.com www.abrohamnealsoftware.com www.sdrsystems.com (540) 242 0911
Amateur Radio: K3NC Blog: http://www.abrohamnealsoftware.com/blog/ DXBase bug reports: email to [email protected] Abroham Neal forums: http:/www.abrohamnealsoftware.com/community/ DX Cluster: dxc.k3nc.com port 23 On Sun, Oct 4, 2009 at 11:38 AM, Eric - VE3GSI <[email protected]> wrote: > Neal, > > There are a number of minor issues I would like to see addressed when > DxBase > is used with my microHAM SO2R+ interface. > > First, there are times I only need DxBase to work on my QSL card responses > or the DxB data base(es) and have no need to 'fire-up' the rig. When I do > this with the microHAM interface powered off and/or mH router not running, > rig connection is turned off automatically by DxB. Needless to say it is > hassle to reconnect the rigs when I next go on the air. > > Along the same train of thought there is no way to see if the Rig is > connected without entering a call on the log book entry line or going into > DxB set-up. It would be great to see the status of frequency/band or mode > reported directly from the rig. > > Next, two-way CW speed control would be a nice addition. That is to say at > the moment I can use DXB to change CW speed but the pot on the mH keyer > does > not echo back to DxBase. > > I run the microHAM SO2R+ interface. It would be great if DxB would switch > rigs (TX Focus) when I choose Rig 1 or Rig 2. If you toss in headphone > routing and you will win the hearts of all us SO2R Ops. > > The CW Transmit Window in DxB does not work properly. I suspect that it > does > not work with any interface. For example if I use the TX window it only > echoes one character at a time. There is NO type-ahead buffer displayed. > > Last, there is no doubt this is NOT a mH issue. Could you please look into > the marriage of MMTTY and MMVARI directly with DxBase. Yes I know of, and > use the 'Bridge Software' but unlike contest software DxB in this > configuration does not give an instant response to a call being entered and > looked up in the logbook. > > Thanks in advance, > Eric - VE3GSI > > > > > > -----Original Message----- > > From: [email protected] [mailto:dxbase- > > [email protected]] On Behalf Of Neal Campbell > > Sent: October-04-09 8:42 AM > > To: DXBase List > > Subject: [Dxbase] Microham support?? > > > > Hi all > > > > In the list of 5 things that needs to improve, there have been a couple > > of > > comments comcerning better support of microHam products. I understand > > the > > comment, in terms of things like the new Station Master device (I have > > one > > so I can test with it no problem!) but what else is there to do? I want > > to > > fully support microHam devices so would appreciate any ideas on what I > > should be considering, > > > > Neal Campbell > > Abroham Neal Software > > www.dxbase.com > > www.abrohamnealsoftware.com > > www.sdrsystems.com > > (540) 242 0911 > > > > Amateur Radio: K3NC > > Blog: http://www.abrohamnealsoftware.com/blog/ > > DXBase bug reports: email to [email protected] > > Abroham Neal forums: http:/www.abrohamnealsoftware.com/community/ > > > > DX Cluster: dxc.k3nc.com port 23 > > ______________________________________________________________ > > Dxbase mailing list > > Home: http://mailman.qth.net/mailman/listinfo/dxbase > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ Dxbase mailing list Home: http://mailman.qth.net/mailman/listinfo/dxbase Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
