These setting are what worked with WriteLog and Ham Radio Deluxe --- DxBase hesitates on 'enter' and then returns no value after a definite stall. Radio #2 my Yaesu works perfect. I have also tried 9600, 8,n,1...
George Nicholson, Jr. -----Original Message----- From: Gary AL9A [mailto:a...@mtaonline.net] Sent: Tuesday, March 09, 2010 8:04 PM To: k1ep.l...@gmail.com; George Nicholson; Dxbase@mailman.qth.net Subject: Re: [Dxbase] Icom 706MKIIG rig interface I've run three different Icom radios with DXB2006, IC-706MKII, IC-756PRO and now the IC-7600, settings at 19200, 8, N, 2 with no problems. 73, Gary AL9A ----- Original Message ----- From: "Ed K1EP" <k1ep.l...@gmail.com> To: "George Nicholson" <geo...@nicholsoncontracting.com>; <Dxbase@mailman.qth.net> Sent: March 09, 2010 5:19 AM Subject: Re: [Dxbase] Icom 706MKIIG rig interface > You must use 8,N,1 for Icoms, you will get intermittent errors if you > use 2 stop bits. It doesn't matter what the CI-V address is, as long > as the radio and the .ini file are the same. Every time Icom came > out with a new radio, it incremented the address just so that they > were different, there is no significance to them. Just make sure > that the two are the same and it will be fine. The 706, 706MkII and > 706MKIIG all have different default addresses from the factory. > > At 3/9/2010 08:41 AM, George Nicholson wrote: >>I used 9600,m,8,1 first the rig did not work with any software using >>those settings. I finally got it working perfect with Writelog and Ham >>Radio Deluxe by changing to 19200, n,8,2 ... I have gone back to your >>suggested settings several times and it's still not working. >> >>I also have verified the rig and the software at address=0X58. I >>actually had to manually change the ini file in Writelog to this address >>to make it work. My version only has the original 706's setting so I had >>to update it to the MKIIg setting. >> >>I am normally pretty good at these things but this one has me after 5 >>hrs of changing combinations of settings... I have a Yaesu and a Kenwood >>both working in DxBase and I have verified all of the check boxes like >>"read from radio" etc... >> >>The software hesitates before moving fields when you hit enter so it's >>trying to read the rig but just can't complete it? >> >>THANKS.... >>George Nicholson, Jr. >>-----Original Message----- >>From: F5CQ Rafik [mailto:f...@f5cq.net] >>Sent: Tuesday, March 09, 2010 8:33 AM >>To: George Nicholson; Dxbase@mailman.qth.net >>Subject: Re: [Dxbase] Icom 706MKIIG rig interface >> >>Setting are : >>9600, n, 8, 1 >> >>In Radios.ini file, the address for MK2G : >>Address=0x58 >> >>73 Rafik, F5CQ >> >>______________________________________________________________ >>Dxbase mailing list >>Home: http://mailman.qth.net/mailman/listinfo/dxbase >>Help: http://mailman.qth.net/mmfaq.htm >>Post: mailto:Dxbase@mailman.qth.net >> >>This list hosted by: http://www.qsl.net >>Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ > Dxbase mailing list > Home: http://mailman.qth.net/mailman/listinfo/dxbase > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Dxbase@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Dxbase mailing list Home: http://mailman.qth.net/mailman/listinfo/dxbase Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Dxbase@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
