> -----Original Message----- > From: Marcin Wojtas [mailto:[email protected]] > Sent: Thursday, October 11, 2018 11:43 PM > To: Wu, Hao A > Cc: Ni, Ruiyu; Ard Biesheuvel; Tian, Feng; Tomasz Michalec; Dong, Eric; edk2- > devel-01; Gao, Liming; [email protected]; Kinney, Michael D; Zeng, Star > Subject: Re: [edk2] [PATCH v2 2/4] MdeModulePkg/SdMmcPciHcDxe: Add > UhsSignaling to SdMmcOverride protocol > > wt., 9 paź 2018 o 13:51 Marcin Wojtas <[email protected]> napisał(a): > > > > wt., 9 paź 2018 o 13:45 Ard Biesheuvel <[email protected]> > napisał(a): > > > > > > On 9 October 2018 at 13:32, Marcin Wojtas <[email protected]> wrote: > > > > wt., 9 paź 2018 o 13:28 Wu, Hao A <[email protected]> napisał(a): > > > >> > > > >> > -----Original Message----- > > > >> > From: edk2-devel [mailto:[email protected]] On > Behalf Of Ard > > > >> > Biesheuvel > > > >> > Sent: Monday, October 08, 2018 11:10 PM > > > >> > To: Marcin Wojtas; Ni, Ruiyu; Wu, Hao A > > > >> > Cc: Tian, Feng; Tomasz Michalec; Dong, Eric; edk2-devel-01; Gao, > Liming; > > > >> > Nadav Haklai; Kinney, Michael D; Zeng, Star > > > >> > Subject: Re: [edk2] [PATCH v2 2/4] MdeModulePkg/SdMmcPciHcDxe: > Add > > > >> > UhsSignaling to SdMmcOverride protocol > > > >> > > > > ... > > > >> > > > > >> > I suppose this is defined by the eMMC spec. > > > >> > > > > >> > Ruiyu, Hao, could you clarify? Are the host control 2 register values > > > >> > for HS200/HS400 defined by the eMMC spec? > > > >> > > > >> Hi Ard and Marcin, > > > >> > > > >> As far as I know, the EMMC Electrical Standard Spec 5.1 (latest) does > not > > > >> mention on how to set the "UHS Mode Select" field of the Host > Control 2 > > > >> Register when switching to HS200/HS400. (Actually, the EMMC spec > does not > > > >> mention Host Control 2 Register at all) > > > >> > > > >> When it comes to setting the bus mode for EMMC devices, the current > > > >> implementation of the SdMmcPciHcDxe driver does a mapping when > setting the > > > >> Host Control 2 Register: > > > >> > > > >> EMMC High Speed SDR - Freq: 0-52 MHz, Data Rate: Single > > > >> matches > > > >> SD SDR25 - Freq: 0-50 MHz, Data Rate: Single > > > >> > > > >> EMMC High Speed DDR - Freq: 0-52 MHz, Data Rate: Dual > > > >> matches > > > >> SD DDR50 - Freq: 0-50 MHz, Data Rate: Dual > > > >> > > > >> EMMC HS200 - Freq: 0-200 MHz, Data Rate: Single > > > >> matches > > > >> SD SDR104 - Freq: 0-208 MHz, Data Rate: Single > > > >> > > > >> EMMC HS400 - Freq: 0-200 MHz, Data Rate: Dual > > > >> matches > > > >> SD None > > > >> > > > >> And there is no obvious counterpart for the EMMC HS400 mode in the > SD > > > >> spec. The driver currently sets the "UHS Mode Select" field to a > reserved > > > >> value 0x5. > > > >> > > > > > > > > Thank you Hao, above is on par with what the default UhsSignaling > > > > routine does in this patch. IMO especially in case the EMMC standard > > > > is not unequivocal regarding UHS_MODE_SEL, I'd encourage to accept > > > > some way of updating HostControl2 register, depending on the > > > > implementation. What is your opinion Ard? > > > > > > > > > > I would like to know where the current values in SdMmcPciHcDxe come > > > from if they are not defined in any spec. > > > > > > How do we know which ones are the correct ones? > > > > Hao, can you justify used values? > > > > Hi Hao, > > Can you please take a look at the UHS_MODE_SEL values source for eMMC?
Hi Marcin, Sorry for the delayed response. For the current implementation of the SdMmcPciHcDxe driver, the selecting of "UHS Mode Select" field value of the Host Control 2 Register is based on a Max Clock Frequency & Data Rate (Single or Dual) matching relationship between the: A. Table 3-6 of the SD Specifications Part 1 Physical Layer Simplified Specification Version 4.10 and B. Table 4 of the EMMC Electrical Standard Spec 5.1 The matching details was included in my previous reply. The only missing part is there seems no matching for the EMMC HS400 mode in the SD specifications. For this case, we are currently using the same approach with the Linux implementation, that is to set the "UHS Mode Select" to a value of 0x5 (not standard). Best Regards, Hao Wu > > Thanks, > Marcin _______________________________________________ edk2-devel mailing list [email protected] https://lists.01.org/mailman/listinfo/edk2-devel
