AFIK, and certainly in UK, the Wanadoo ISP is far from Freemail. I'm on Freeserve which is the UK Name for Wanadoo and I have never experienced a bounce because of my ISP's policies. I can't offer any good reasons why they are bouncing though sO I suppose I had better stop using bandwidth. 73 Mike G8NXD --
On 9 Apr 2005 at 10:09, Martin Kratoska wrote: > It seems that the general settings of spam filtering is the culprit. > Some ISP blocking mass freemail providers (yahoo.com, aol.com etc.). > An email address change is the solution. > > 73 Martin OK1RR > > > F5UL napsal(a): > > May be out of order on this reflector, but yesterday I had a mssage > > to post concerning a big trouble with my K2 SN 4498 and the > > following was all what I got in return...!!! So what can I do to > > post an e-mail from Europe????????????? Thank you very much for the > > pass band ! F5UL > > -------------------------------------------------------------------- > > -------- -------------------------------------------------- > > > > Reporting-MTA: dns; wanadoo.fr > > X-SMTP-Server-Queue-ID: 8B4D31C00152 > > X-SMTP-Server-Sender: rfc822; [EMAIL PROTECTED] > > Arrival-Date: Fri, 8 Apr 2005 22:47:17 +0200 (CEST) > > > > Final-Recipient: rfc822; [email protected] > > Action: failed > > Status: 5.0.0 > > Diagnostic-Code: X-SMTP-Server; host > > > > -------------------------------------------------------------------- > > -------- ------------------------------------------------- Hello the > > list, Up to this morning, this K2 was a nice and good worker, with > > during the last six month about a thousand QSO under his belt ! But > > this morning turning it on, I just got a vigorous howl ( very low > > freq nois !). I turn it off, and on after a few second. The Rx start > > normaly and the noise start again after a few second. Re-turn off > > and tunr on and no howl and Rx is working correctly! The set was in > > CW mode so I turn down power (to abt 2/3 watts) and close the key... > > The result is correct on 1.8, 3.5, 7.0 but nil on the rest of the > > bands. Closing the key a little longer on 7.0 the rig goes to > > curent overange in abt 10/12 second and power fall down to zero. So > > power off, open the rig, remove the bottom cover and before removing > > the heat sink just check the resistance of driver and PAOn Q6 > > (driver) E to Gnd 1.3 ohm, B to Gnd 76/80 ohms, and C to Gnd > 500 > > ohms. On Pa C to Gnd > 600 ohms, B to Gnd 120/130 ohm E to Gnd 0 > > (it's normal!)They seems to be normals but any time I close the key > > I get High Cur and power out ZERO !! I do n,ot know what to do so I > > will wait till tomorow and hope to get some indications from the > > list ! Thanks in advance guy, BCNU 72 Bob/F5UL > > > > > > > > > > _______________________________________________ > > Elecraft mailing list > > Post to: [email protected] > > You must be a subscriber to post to the list. > > Subscriber Info (Addr. Change, sub, unsub etc.): > > http://mailman.qth.net/mailman/listinfo/elecraft > > > > Help: http://mailman.qth.net/subscribers.htm > > Elecraft web page: http://www.elecraft.com > > > > _______________________________________________ > Elecraft mailing list > Post to: [email protected] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > _______________________________________________ Elecraft mailing list Post to: [email protected] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
