Make sure DTBL0014.HEX is in the folder along with the DSP files. That's the DSP table for DSP 2.71. Then reload the DSP. I think this is the same kind of problem that you had with the FP -- out-of-sync files.
On 1/30/2011 3:02 PM, Jim Harris wrote: > Vic, > > As you suspected the problem with the menu misalignment was the front panel > firmware > revision. Somehow yesterday when I had the utility download all the latest > firmware it > downloaded 1.09. Today it found 1.14. I've installed it and the menu problem > is resolved. > Strange how it found the right one today but not yesterday. > > However, function of the APF is unchanged from what I've described below. > That is a loud > clip when engaged, CW disappears and then when rotating the shift control > there is a loud > clip when each 50 Hz step is incremented. I've read the manual to no help. > Any clues from > anyone would be helpful and appreciated. > > Take pride in the USA. 73 > > Jim, W0EM > > --- On *Sun, 1/30/11, Jim Harris /<[email protected]>/* wrote: > > > From: Jim Harris <[email protected]> > Subject: K3 APF Problem > To: [email protected], [email protected] > Date: Sunday, January 30, 2011, 10:40 PM > > Vic, > > Thank you for the response. You may be heading me in the right direction. > I had the K3 > Utility download the latest of all the firmware's from the website and > told it to > install them. It shows it downloaded and installed FPF 1.09. You mention > it should be > 1.14. I'll try to find it on the site, download and install it and see > what happens. > > Strange that what should apparently be the latest release is not directly > available > when the Utility checks the website. That creates problems for people > like me. > > I'll post results when there is something new. > > Take pride in the USA. 73 > > Jim, W0EM > > Date: Sat, 29 Jan 2011 17:18:53 -0800 > From: Vic K2VCO <[email protected]> > Subject: Re: [Elecraft] K3 APF Problem??? > To: [email protected] > Message-ID: <[email protected]> > Content-Type: text/plain; charset=ISO-8859-1; format=flowed > > Make sure that the front panel code is also updated. The proper version > for 4.25 is 1.14. > Also make sure the proper DSP table is present when you update; it should > be > DTBL0014.HEX. > If all the versions aren't synchronized you can have problems like you > describe. > > On 1/29/2011 2:27 PM, Jim Harris wrote: > > Hi Folks, > > > > After watching the progress of APF for a few months I decided it was > time to upgrade to > > the latest firmware (4.25) and give it a try. When pressing the DUAL > PB there is a > > LOUD clip and the CW is gone. Turning the SHIFT control products one > LOUD clip for > > each 50 Hz step. I went to CONFIG and could not find DUEL PB to > ascertain APF was > > selected. Now this gets complicated so follow closely. There is no > DUEL PB in the VFO > > B space between DIGOUT1 and EXT ALC as the latest manual (D9 - Pg 55) > indicates there > > should be. However, when EXT ALC is selected APF is show in VFO A. It > appears that in > > my K3 all values in the second column of the manual (displayed in VFO > A) beginning with > > EXT ALC is shifted up one entry from the first column of the manual > (displayed in VFO > > B). BTW, turning VFO A knob does change the VFO A display from APF to > DUEL PB and back > > again when in EXT ALC. > > > > I have taken a picture and will be happy to display it someplace if > anyone is > > interested in seeing it. > > > > I've read the verbiage on page 35 about APF and there is nothing there > that seems to > > help. Anyone have any ideas or can tell me what I'm doing wrong. > > > > Take pride in the USA. 73 > > > > > > > > Jim, W0EM > > > -- Vic, K2VCO Fresno CA http://www.qsl.net/k2vco/ ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
