Check your filter locations and make sure they are "selected". As I recall you must instal the filters in slot 1 then 2 then 3. In other words, no skipping over slots.
Craig Buck On Nov 28, 2012, at 6:19 PM, "Mike Sanders" <[email protected]> wrote: > Well, I think I have found it. I have not gotten > the filters selected for the sub RX and the rig > keeps going back to a FL1 position. I only > have FL2 and FL4 populated with 2.8 and > 400hz respectively. When I go into Bset I > can get to those filters and the RX is FB > but when I get out of Bset it goes back to > one of the filter slots I do not have. > Apparently I need to deselect FL1, 3 and > 5 from the sub RX. Not sure How to do that? > Thanks for the tips so far. Any help on the > filter issue appreciated. 73 again. > > > > Mike Sanders > KØAZ > > > > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]]On Behalf Of Cady, Fred > Sent: Wednesday, November 28, 2012 16:55 PM > To: Elecraft Reflector > Subject: Re: [Elecraft] Sub RX no work > > > Hi Mike, > Make sure the sub rx and the main rx are on the same antenna. Turn Sub on > and then Hold RX until you see MAIN displayed, not AUX. > 73 and cheers, > Fred KE7X > > Fred Cady > fcady at ieee dot org > >> -----Original Message----- >> From: [email protected] [mailto:elecraft- >> [email protected]] On Behalf Of Mike Sanders >> Sent: Wednesday, November 28, 2012 3:51 PM >> To: Elecraft Reflector >> Subject: [Elecraft] Sub RX no work >> >> Greetings All, Well I have just installed a sub RX in a late >> K3 (67xx). Before I go back into the radio and quadruple >> check my work I just have to ask if I am missing something >> in config. >> I have audio and control of the sub RX and can even hear >> signals through it but very very weak compared to the Main. >> All seems OK but just very poor RX. I have selected the >> ATU as source of antenna and have my connections there. >> (I will go in later and see if I have any thing mis/dis connected). >> Am I missing something in config? I have two filters installed >> in the sub and NO BPF. No error messages and again it >> seems to respond to everything input to it. Even receives >> just poorly. Thanks for any help. 73, Mike >> >> >> Mike Sanders >> KØAZ >> >> >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > Version: 10.0.1427 / Virus Database: 2629/5424 - Release Date: 11/28/12 > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
