Ok could be undocumented. Lets hope Wayne chimes in. Tom va2fsq.com
Sent from my iPhone On 2013-07-17, at 5:25 PM, William Levy <[email protected]> wrote: > Not what Wayne says. > > On Jul 17, 2013, at 3:24 PM, Tom <[email protected]> wrote: > >> >> Hi >> Yes they talk to each other but only send band change info and certain other >> statuses. To do this with only a macro and no possible hardware is not >> possible >> >> Tom >> va2fsq.com >> >> Sent from my iPhone >> >> On 2013-07-17, at 5:06 PM, William Levy <[email protected]> wrote: >> >>> Yes, but they are connected directly in the back of the K3 with one of the >>> AUX cables so they feed each other that way. >>> Thus the K3, Amp and ATU all talk to each other. >>> Thus the need to be able from the K3 to turn on the Amp. >>> Bill N2WL >>> >>> >>> On Jul 17, 2013, at 1:02 PM, Tom wrote: >>> >>>> Hi >>>> That would be news to me, since the k3 and kpa use different serial ports. >>>> Tom >>>> va1fsq.com >>>> >>>> Sent from my iPhone >>>> >>>> On 2013-07-17, at 2:24 PM, William Levy <[email protected]> wrote: >>>> >>>>> Somewhere I thought there was written a short macro to designate a button >>>>> on the K3 to turn on the Amp from the K3. >>>>> >>>>> Any help with that would be greatly appreciated. This old ham has his fist >>>>> in to too many old radios at the moment to sit down and figure out code. >>>>> Too busy reading resistor codes. All help appreciated. Thanks, Bill N2WL >>>>> ______________________________________________________________ >>>>> Elecraft mailing list >>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>>> Help: http://mailman.qth.net/mmfaq.htm >>>>> Post: mailto:[email protected] >>>>> >>>>> This list hosted by: http://www.qsl.net >>>>> Please help support this email list: http://www.qsl.net/donate.html >> Sent from my iPhone >> >> On 2013-07-17, at 5:06 PM, William Levy <[email protected]> wrote: >> >>> Yes, but they are connected directly in the back of the K3 with one of the >>> AUX cables so they feed each other that way. >>> Thus the K3, Amp and ATU all talk to each other. >>> Thus the need to be able from the K3 to turn on the Amp. >>> Bill N2WL >>> >>> >>> On Jul 17, 2013, at 1:02 PM, Tom wrote: >>> >>>> Hi >>>> That would be news to me, since the k3 and kpa use different serial ports. >>>> Tom >>>> va1fsq.com >>>> >>>> Sent from my iPhone >>>> >>>> On 2013-07-17, at 2:24 PM, William Levy <[email protected]> wrote: >>>> >>>>> Somewhere I thought there was written a short macro to designate a button >>>>> on the K3 to turn on the Amp from the K3. >>>>> >>>>> Any help with that would be greatly appreciated. This old ham has his fist >>>>> in to too many old radios at the moment to sit down and figure out code. >>>>> Too busy reading resistor codes. All help appreciated. Thanks, Bill N2WL >>>>> ______________________________________________________________ >>>>> Elecraft mailing list >>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>>> Help: http://mailman.qth.net/mmfaq.htm >>>>> Post: mailto:[email protected] >>>>> >>>>> This list hosted by: http://www.qsl.net >>>>> Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
