Tom,
Think about it a bit. The K3 ACC cable connects to the KPA500 for the
band data only. So how could any form of a command be passed over the
band data lines?
73,
Don W3FPR
On 7/17/2013 5:29 PM, Tom wrote:
Ok could be undocumented.
Lets hope Wayne chimes in.
Tom
va2fsq.com
Sent from my iPhone
On 2013-07-17, at 5:25 PM, William Levy <[email protected]> wrote:
Not what Wayne says.
On Jul 17, 2013, at 3:24 PM, Tom <[email protected]> wrote:
Hi
Yes they talk to each other but only send band change info and certain other
statuses. To do this with only a macro and no possible hardware is not possible
Tom
va2fsq.com
Sent from my iPhone
On 2013-07-17, at 5:06 PM, William Levy <[email protected]> wrote:
Yes, but they are connected directly in the back of the K3 with one of the AUX
cables so they feed each other that way.
Thus the K3, Amp and ATU all talk to each other.
Thus the need to be able from the K3 to turn on the Amp.
Bill N2WL
On Jul 17, 2013, at 1:02 PM, Tom wrote:
Hi
That would be news to me, since the k3 and kpa use different serial ports.
Tom
va1fsq.com
Sent from my iPhone
On 2013-07-17, at 2:24 PM, William Levy <[email protected]> wrote:
Somewhere I thought there was written a short macro to designate a button
on the K3 to turn on the Amp from the K3.
Any help with that would be greatly appreciated. This old ham has his fist
in to too many old radios at the moment to sit down and figure out code.
Too busy reading resistor codes. All help appreciated. Thanks, Bill N2WL
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Sent from my iPhone
On 2013-07-17, at 5:06 PM, William Levy <[email protected]> wrote:
Yes, but they are connected directly in the back of the K3 with one of the AUX
cables so they feed each other that way.
Thus the K3, Amp and ATU all talk to each other.
Thus the need to be able from the K3 to turn on the Amp.
Bill N2WL
On Jul 17, 2013, at 1:02 PM, Tom wrote:
Hi
That would be news to me, since the k3 and kpa use different serial ports.
Tom
va1fsq.com
Sent from my iPhone
On 2013-07-17, at 2:24 PM, William Levy <[email protected]> wrote:
Somewhere I thought there was written a short macro to designate a button
on the K3 to turn on the Amp from the K3.
Any help with that would be greatly appreciated. This old ham has his fist
in to too many old radios at the moment to sit down and figure out code.
Too busy reading resistor codes. All help appreciated. Thanks, Bill N2WL
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
