Can you hear signals in CW mode with both narrow and wide Xtal filters? Please look into schematic diagram and using the signal generator try to find where the signal is lost in front-end or IF chain. Go backwards from AF to front-end. 73, Victor Goncharsky US5WE/K1WE (UW5W in VHF contests) UARL Technical Committee DXCC card checker in Ukraine(160 meters). -------------------------------------------- On Thu, 10/24/13, Tommy <[email protected]> wrote:
Subject: [Elecraft] FW: K3 - SSB audio get lost ! To: [email protected] Date: Thursday, October 24, 2013, 2:22 AM From: Tommy [mailto:[email protected]] Sent: Wednesday, October 23, 2013 10:17 PM To: '[email protected]' Subject: RE: [Elecraft] K3 - SSB audio get lost ! Thanks to all asking about my filter configuration. I have my 2.7kc/1.0kc/0.5kc/0.3kc filters all enabled for CW/ LSB/ USB/ and DATA. And to clarify my original post, I am talking about receive audio and not transmitted audio. 73, Tom - W4BQF From: John Parker [mailto:[email protected]] Sent: Wednesday, October 23, 2013 10:04 PM To: Tommy Subject: Re: [Elecraft] K3 - SSB audio get lost ! Is it possible that your 2.7/2.8 Khz filter is not selected for SSB in the configuration? Good luck with this, 73, John WB4UHC _____ From: Tommy <[email protected] <mailto:[email protected]> > To: [email protected] <mailto:[email protected]> Sent: Wednesday, October 23, 2013 10:39 AM Subject: [Elecraft] K3 - SSB audio get lost ! I am having a configuration issue that I have spent hours trying to figure out and need some help please. As a CW person, I seldom operate SSB and I am trying to get set up for this weekend's CQWW SSB test. Below are some of my configuration for my K3 and the attached are jpg configuration sheets from K3 EZ. In any band in the SSB portion, I have no audio output any time I am in the USB or LSB mode, however if I change from USB to CW, I have normal audio but of course I can't copy the SSB signals. This is true whether I have my SUB turned on or not. I have my CM-500 headset plugged into the rear of my K3 and I have the RS20S headset plugged into the front panel PHONES jack and I have no audio with either or both of the headsets plugged in. With both headsets removed, I have no speaker audio in the SSB mode, but normal audio in the CW or AM mode. Any helpful suggestions would be greatly appreciated! In CONFIG I have: SPKRS = 1 SPKR+PH = YES L-MIX-R = A b Thanks for your input and 73, Tom - W4BQF PS: I have been trying to configuration pictures from K3-EZ but nothing is getting onto the reflector. ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] <mailto:[email protected]> This list hosted by: http://www.qsl.net <http://www.qsl.net/> Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
