Follow the audio setup instructions in the microHAM Users Manual.
If you do not receive the expected results at a given step, find
out why right away as each step builds on the previous step.
When you are in voice modes the LINE LED on MK II should be OFF
(or blinking if recording to the DVK). If it is red some program
(or Windows) has taken control of microHAM CODEC and selected the
LINE input. Again, follow the set-up instructions in the User's
Manual. It is impossible to guess what is set incorrectly but
something is most certainly set incorrectly as I use MK II and K3
every day with a headset connected to the EXT Mic (front of the
MK II).
73,
... Joe, W4TV
On 12/27/2013 11:08 AM, [email protected] wrote:
Hi,
Still no luck at all. The two jumpers are set as follows:
The jumper near the pots is set to EL (both posts covered).
The Jumper set at the left of the board is set to IC as per the manual
The RJ45 is plugged in the back. The Heil proset headphones are plugged in the
front headphone jack on the K3, the mic is plugged via the foster to the RJ45
cable in rear.
The audio that I hear through the headset is fine. If I try VOX, nothing
happens(it is set) . If I press XMIT on the transmitter , the transmitter goes
into transmit and I try to talk no audio output from the MIC and no RF going
out.
While the microham is sitting there, the lights on it are
Line is red.
\When I press a string to be transmitted in DM780, the PTT2 comes on and the SC
light comes on.
But I do not hear a signal.
The elecraft K3 "Mic" is set RPl.
Clicking on the sound card in Microham
I select Headset Earphone(microham Coded) for Wave Out
Line (Microham CODEC
Mixer Line. (Microham Codex
If I press Test in this window K3 goes into transmit,
Line stays red
PTT2 comes on
SC comes on and Front panel says playing. I hear nothing though just silence.
If I adjust everything associated with the microham to max in the mixers, I
never hear anything on any of the test modes.
I'm at a loss here.
Is it sure that the microham cables LINE IN plus into LINE IN on the K3?
If I plug the mic in the from panel of the microham there is no difference.
Slow going here.
Thanks for any hjelp
Same thing if I try DM780, sending a
On 12/26/13, "Joe Subich, W4TV" <[email protected]> wrote:
Pi am using a Heil preset as received from Elecraft. I have the k3
front mic cable. I have the wire marked line in on the cable to the
line in on the radio. Same for line out. I have set jumpers to non
electret. Can someone tell me what I am doing wrong.?
Elecraft ProSet has an ELECTRET mic you need to set the jumpers in
MKII for electret in order to supply the necessary power to the mic
element and then perform the audio level set-up as documented in the
MKII Users Manual.
73,
... Joe, W4TV
On 12/26/2013 12:37 PM, Tom wrote:
Hi, I just hooked up my Microkeyer 2 installed all software and the
software is communicating with the radio. However if I talk into my
Mike there is no transmit occurring via Vox or PTT on the radio. Pi
am using a Heil preset as received from Elecraft. I have the k3 front
mic cable. I have the wire marked line in on the cable to the line in
on the radio. Same for line out. I have set jumpers to non electret.
Can someone tell me what I am doing wrong.? Thanks
______________________________________________________________
Elecraft mailing list Home:
http://mailman.qth.net/mailman/listinfo/elecraft Help:
http://mailman.qth.net/mmfaq.htm Post:
mailto:[email protected] <[email protected]>
This list hosted by: http://www.qsl.net Please help support this
email list: http://www.qsl.net/donate.html
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected] <[email protected]>
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
