When a station is zero beat with me, I hear him at my sidetone frequency. I understand that in a round table situation there will be some stations that won't be zero beat for a multitude of reasons.
BTW, my copying speed is going down, down, down. I haven't heard Lyle or you in a looong time. 73 John/K4WJ ex KN8PXG K8PXG ZF2HZ Sent from my iPad > On Feb 17, 2014, at 12:38 PM, "Chester Alderman" <[email protected]> > wrote: > > But if you have several hams in the round-table, you sure do need RIT because > you know all hams are not going to be zero beat. Besides that, yes, ever if > your one QSO partner is zero beat, you need the ability to slightly change > the Rx QRQ frequency so the received tone suits your ears. Copying QRQ > requires one to be able to use standard CW receiver functions. That is why I, > personally, can't use my K3 for full QSK QRQ operation. > Since this issue has been on-going for several years, it most likely can not > be fixed? Or it is just being ignored! > > 73, > Tom - W4BQF > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of John Bohnovic > Sent: Monday, February 17, 2014 11:36 AM > To: Klaus Koppendorfer > Cc: Elecraft Reflector; [email protected] > Subject: Re: [Elecraft] CW QRQ and SPLIT > > Do you need the RIT mode when the other station is zero beat with your signal? > > John/K4WJ > ex KN8PXG K8PXG ZF2HZ > Sent from my iPad > >> On Feb 17, 2014, at 3:05 AM, Klaus Koppendorfer <[email protected]> wrote: >> >> It is sad that QRQ mode has no RIT !!! >> Cw up from 30 to 35 WPM hast o use QRQ mode because of struggling dits >> and dahs >> >> Many highspeed ops VHSC EHSC has changed from k3 to FT5000 because of >> leaking RIT with QRQ with K3 >> >> Maybe Wayne will sharpen Firmware in future for QRQ mode >> >> If rit/split is necessary i use 2nd RX but this is not so comfortable >> >> 73 >> Oe6kyg >> Klaus >> >> >> -----Ursprüngliche Nachricht----- >> Von: [email protected] >> [mailto:[email protected]] Im Auftrag von Don Wilhelm >> Gesendet: Samstag, 15. Februar 2014 22:06 >> An: Jorge Diez - CX6VM; 'Elecraft Reflector' >> Betreff: Re: [Elecraft] CW QRQ and SPLIT >> >> Jorge, >> >> AFAIK, probably not. The frequency must be shifted from RX to TX, and with >> QRQ in effect it is not possible to shift that fast. A K3 with 'chirp' on >> the ham bands would not be a nice thing to hear. >> >> 73, >> Don W3FPR >> >>> On 2/15/2014 2:33 PM, Jorge Diez - CX6VM wrote: >>> I saw in the manual of K3 that CW QRQ is "temporarily turned OFF" >>> with SPLIT. >>> >>> Will be in the future any way to use it in SPLIT mode or is impossible? >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net Please help support this email >> list: http://www.qsl.net/donate.html >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net Please help support this email >> list: http://www.qsl.net/donate.html > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
