Jim,
I highly suggest that you post this issue on the RemoteRig forum at
http://www.remoterig.com/forum/index.php for the RemoteRig developers to
answer. They do not read the Elecraft reflector.
73,
Mitch DJ0QN
Mitch Wolfson
DJØQN / K7DX
Neubiberger Str. 21, 85640 Putzbrunn
Skype: mitchwo - Home:+49 89 32152700 - Mobile:+49 172 8374436
Echolink: 3001 - IRLP: 5378
On 05.08.2014 17:33, Jim - KE8G wrote:
I now see I have an error message on the remote side:
Saved error message:
Data Abort at 0x00043114, called by 0x000437ac
Any ideas?
---- KE8G <[email protected]> wrote:
Well, the unfortunate part is that the only description I got was the radio
sounded like it has a defect, nothing more and the fellow was gone. If someone
would like to setup a sked to have a listen, that would be great. It would
have to be a CW sked, as I do not have a mic.
To update everyone commenting, I have updated the K3 firmware at the control
end, so both are now at the same level. The firmware on the RemoteRig units
are identical, no changes had been made there. The coax for the remote station
is all new 400Max series fromDXEngineering, which was thoroughly tested when
installed two months ago.
I will update the RemoteRig firmware at both sites and see if that changes
anything.
Thanks all for you comments!
73 de Jim - KE8G
Sent from my iPad
On Aug 4, 2014, at 11:05 PM, Mike va3mw <[email protected]> wrote:
What is the actual problem? Defect doesn't really describe anything.
I would check the readme and see if both ends need to be updated. I would
suspect so. Why not upgrade the other end just to be sure.
Btw, SWR being good or bad won't really tell you much other than if your coax
is presenting a 50 ohm load. It certainly won't create a bad audio situation.
Mike va3mw
On Aug 4, 2014, at 10:22 PM, Jim - KE8G <[email protected]> wrote:
Hi All,
I seem to be having a problem with my RemoteRig operation. Everything worked
perfectly when I initially set it up. While at the remote QTH, the only change
I made was to add the newest firmware to the K3. I have not updated the
firmware at the K3 control station, would this cause a problem?
I had a person tell me the rig sounds like it has a "defect."
Looking at things from the control end, the KAT500 & KPA500 both appear fine,
no changes in SWR or power output.
Any ideas?
73 de Jim - KE8G
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
