I do not have ACOM2000 but I use the same arrangement with Expert 1-KFA and
K3. Logging program polls the radio and the amp only "listens" for K3
response to learn the operating freq. When you terminate logger there is no
polling anymore. Therefore the system does not work as expected. This is
normal.
73, Igor UA9CDC
----- Original Message -----
From: "Bill Turner" <[email protected]>
To: <[email protected]>
Cc: "Elecraft" <[email protected]>
Sent: Saturday, September 13, 2014 5:53 AM
Subject: Re: [Elecraft] [acom-list] Re: Elecraft K3 and ACOM 2000A
My cable is store bought, and it is the kind in figure 7.2, i.e.
without the TXD wire. I ohmed it to be sure. Actually, it is a cable
with a separate Y adaptor, but the effective wiring is the same as
figure 7.2.
And here's the kicker: This morning when I fired up everything to do
some more troubleshooting, everything worked just as it should. It
seems I have an intermittent connection somewhere, most likely in a
cable, connector or the Y adaptor. It's been working fine all day.
I think I will build a new cable and Y adaptor to eliminate that as a
possible cause and see if the problem stays gone.
I did notice one thing that seems odd. When I do not have a logging
program running and I do a manual band change on the K3, the ACOM does
not follow the change. I thought it should. Does your's work that way?
As soon as I start a logging program, everything returns to normal.
Don't you just love these intermittent gremlins? :-)
73, Bill W6WRT
------------ ORIGINAL MESSAGE ------------(may be snipped)
On Fri, 12 Sep 2014 18:47:48 -0400, Nick wrote:
Hi Bill
Did you build your cable according to schematic on page 34 (figure 7-6)
from Acom 2000 manual? This wiring diagram is for K3 CAT with ACOM 2000A
only. I believe this diagram assumes there is no computer connected in.
It only describes the case in which there is a connection between the K3
and Acom 2000A.
If you look at the page 32 (Fig 7-2) which describes the "generic" wiring
between RS232 PC port and Transceiver with ACOM connected via "Y" cable,
you will notice that they only use the RXD wiring and the ground. TXD
line has been omitted.
RCU DB15 Pin 1 <-------> RS-232 Pin 2
RCU DB15 Pin 5 <-------> RS-232 Pin 5 (Ground)
I initially built the CAT cable using all 3 wires (RXD, TXD + Ground) and
as soon as ACOM would come online, K3 would not work properly with my
LP-PAN and LP Bridge. I don't use P3.
I snipped the TXD line after reading your email and now everything appears
to be working fine. K3+ACOM2000A+PC are tracking frequency smoothly like
usual.
If I now just type the frequency in Win-Test or change the band on my K3,
ACOM nicely parks itself on a whichever band segment it detects by
sniffing
the comm traffic between K3 and the PC.
73, Nick
ve3ey
On Fri, Sep 12, 2014 at 6:18 AM, Bill Turner <[email protected]> wrote:
------------ ORIGINAL MESSAGE ------------(may be snipped)
On Fri, 12 Sep 2014 08:46:23 -0000, you wrote:
>Bill,
> I too use the Acom 2000A and do not know why you bother with so
> many
>control cables. The Acom switches bands in a dit or syllable and
>tunes
in
>three seconds automatically. I must be missing something but why do
>you
>need to go to so much trouble with control cables for the amplifier.
REPLY:
The reason I bother is I do not like transmitting even a single dit
into an amplifier on the wrong band at full power. Yes, the ACOM is a
tough amplifier but I am pretty conservative about such things. When I
do send a dit to change bands, I reduce the drive power way down. If I
can get the automatic band change to work, I won't have to reduce
power or send a dit. It will already be pre-tuned.
73, Bill W6WRT
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
