Thanks Matt, Not sure why I did not think of that... The radio is staying in LSB in all cases, so it is something both MixW and FLDigi are doing... -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net for MixW support see; http://groups.yahoo.com/neo/groups/mixw/info for Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info for MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info
On Wed, 2014-11-05 at 03:17 +1100, Matt VK2RQ wrote: > To understand what sideband the radio is on in CW mode, listen to the radio's > speaker and tune up the band. If the signals you hear go UP in pitch as you > tune UP the band, it is using LSB. If the pitch of the signals goes DOWN as > you tune UP the band, the radio is using USB. Once you understand whether the > radio is set to use LSB or USB for a particular band, you can then set your > digital mode software to match. > > 73, > Matt VK2RQ > > > On 5 Nov 2014, at 2:58 am, David Cole <[email protected]> wrote: > > > > Hi Mike, > > Thanks for that input... I am unable to triage this to radio changes, > > or MixW changes... You are correct about MixW. I run the MixW Yahoo > > support group, and the author has been MIA for about three years now... > > He did an update a gew years ago, then dropped off the map again... > > Getting changes from MixW will not happen... > > > > I really want to understand this... It is happening with FLDigi as well, > > so two of the top packages are affected... > > > > I wish I knew EXACTLY what MixW did when I checked or unchecked CW is > > LSB, and why FLDigi simply fails for two people here... > > -- > > Thanks and 73's, > > For equipment, and software setups and reviews see: > > www.nk7z.net > > for MixW support see; > > http://groups.yahoo.com/neo/groups/mixw/info > > for Dopplergram information see: > > http://groups.yahoo.com/neo/groups/dopplergram/info > > for MM-SSTV see: > > http://groups.yahoo.com/neo/groups/MM-SSTV/info > > > > > >> On Tue, 2014-11-04 at 07:51 -0800, Mike Flowers wrote: > >> I also ran MixW and had similar problems with the K3. I sent a lot of > >> information about this problem to the MixW authors, but there was no > >> response and no fix. In fact, it's been years since there was a MixW > >> update. > >> > >> So I chucked MixW and converted my digital operations to HRD - and that was > >> the end of those problems. > >> > >> Not the solution for everyone, but now the HRD suite runs the operation > >> here. > >> > >> - 73 and good DX de Mike, K6MKF, President - NCDXC, IDXC 2015, W6NAG, IDXG, > >> ADXG, RRC #933, K3-P3-KPA500-KAT500 Addict, Maui > >> > >> > >> -----Original Message----- > >> From: Elecraft [mailto:[email protected]] On Behalf Of Rick > >> Bates, WA6NHC > >> Sent: Tuesday, November 04, 2014 7:33 AM > >> To: rs500 > >> Cc: [email protected] > >> Subject: Re: [Elecraft] OK... I give up on what is happening... > >> > >> Since it is running via a serial port, is it possible that the software is > >> overrunning the buffers? Too much data, too fast? If it were close, that > >> would certainly cause an issue that could require a reset of the system. > >> > >> Rick, WA6NHC > >> > >> PS It ain't pretty, but I'm doing the happy dance, Tromelin at LAST! > >> > >> iPad = small keypad = typos = sorry ;-) > >> > >>> On Nov 4, 2014, at 7:26 AM, rs500 <[email protected]> wrote: > >>> > >>> Dave, you are not alone. I have observed the same issue on my K3. I > >>> am running a Signalink and FLDigi. Changing the Mode does seem to > >>> reverse the direction on the waterfall but then I no longer trust the > >> frequency display. > >>> What I have found that consistently solves the problem (until the next > >>> occurrence) is using the K3 Utility program to restore a saved > >>> configuration. Unfortunately I need to close FLDigi in order for the > >>> utility program to connect to the K3. > >>> I have not definitively identified a set of events that causes the > >>> problem, but it seems reasonable that it is a communication problem on > >>> the serial port. I already have a variety of ferrite beads on the > >>> serial port and other cables to the computer. Good luck > >>> > >>> Ron > >>> K2RAS > >>> > >>> > >>> > >>> -- > >>> View this message in context: > >>> http://elecraft.365791.n2.nabble.com/OK-I-give-up-on-what-is-happening > >>> -tp7594377p7594388.html Sent from the Elecraft mailing list archive at > >>> Nabble.com. > >>> ______________________________________________________________ > >>> Elecraft mailing list > >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >>> Help: http://mailman.qth.net/mmfaq.htm > >>> Post: mailto:[email protected] > >>> > >>> This list hosted by: http://www.qsl.net Please help support this email > >>> list: http://www.qsl.net/donate.html Message delivered to > >>> [email protected] > >> ______________________________________________________________ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:[email protected] > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: http://www.qsl.net/donate.html Message > >> delivered to [email protected] > >> > >> ______________________________________________________________ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:[email protected] > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: http://www.qsl.net/donate.html > >> Message delivered to [email protected] > > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
