Below... On Sun, Nov 9, 2014 at 8:58 AM, David Cole <[email protected]> wrote:
> Hi Ken, > I am in CW mode... It acts exactly as you describe, but when in CW > mode, I never see the REV below CW, and I have checked, the rig stays in > CW mode... > When in CW do a HOLD on MODE ALT. This will toggle between CW and CW REV. I always use CW REV. I have to have the higher audio tone in the speaker be the higher actual frequency on the band, so I keep my CW setting based on USB, thus CW REV. Personally, I don't understand why folks prefer the other, but to each his own :>) Most of the guys at NY4A multi-op station use CW not CW REV. I almost always have to toggle CW to CW REV when I first sit down to a position. 73, Guy. > > There is some difference between this rig and the Pro III, and II... > This issue never happened using the Icom rigs. It strikes me that as > long as I am in CW, and not CW REV, everything should be the same, and > NOTHING should matter... However, something is not the same... Right > now I am suspecting that something is different in MixW, but I have my > old .ini file from the Pro III days, and the setup looks the same so > far... I am going through it line by line... > > > -- > Thanks and 73's, > For equipment, and software setups and reviews see: > www.nk7z.net > for MixW support see; > http://groups.yahoo.com/neo/groups/mixw/info > for Dopplergram information see: > http://groups.yahoo.com/neo/groups/dopplergram/info > for MM-SSTV see: > http://groups.yahoo.com/neo/groups/MM-SSTV/info > > > On Sun, 2014-11-09 at 07:44 -0500, Ken wrote: > > Which DATA mode you are in affects the sideband selection. DATA MODE > A normally uses USB for all bands (see the Elecraft manual on "Data Mode > Selection", page 31 in may manual. It's easy to end up with a > different Data Mode and then things vary band to band. When you activate > the Data Mode button, it shows USB or LSB. If you change data mode, or > the sideband selection, I believe those are saved on a per band basis, so > when come back to a band, you get the last selection. You might have to go > through and correct it on all the bands individually. > > > > Ken WA8JXM > > > > On Nov 4, 2014, at 10:26 AM, rs500 wrote: > > > > > Dave, you are not alone. I have observed the same issue on my K3. I > am > > > running a Signalink and FLDigi. Changing the Mode does seem to > reverse the > > > direction on the waterfall but then I no longer trust the frequency > display. > > > What I have found that consistently solves the problem (until the next > > > occurrence) is using the K3 Utility program to restore a saved > > > configuration. Unfortunately I need to close FLDigi in order for the > > > utility program to connect to the K3. > > > I have not definitively identified a set of events that causes the > problem, > > > but it seems reasonable that it is a communication problem on the > serial > > > port. I already have a variety of ferrite beads on the serial port and > > > other cables to the computer. Good luck > > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to [email protected] > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
