Hi Joel, I will look into doing just that. Still looking for an answer about VOX SET and if the command exists yet.
Freeing up PF2 for the setup I use on SOTA would be a real bonus-I use a Heil Headset and usually have to manually set that up on the mountain. 73 K5RHD /randy On Fri, Nov 28, 2014 at 8:09 PM, Joel Black <[email protected]> wrote: > Randy, > > If you wish, you can make them so each macro calls the other: one long > hold brings up the data mode; the second long hold brings up voice; another > long hold brings up data; and so on. > > I don’t have my KX3 out at the moment, but here’s what my macro looks like > going from CWSPLT to UNSPLT: > > CWSPLT - MD3;SWT25;SWT25;FT1;SB1;UPB4;MN142;MP001;MN110;SWT27;SWH18;MN255; > UNSPLT - SB0;FR0;MN142;MP000;MN110;SWT19;SWH18;MN255; > > The last four commands of CWSPLT tell it MN110 (MACRO x); SWT27 (x=2); > SWH18 (program PF1 [with Macro 2 {from SWT27 where x=2}]); MN255 (exit > menu). > > The last four commands of UNSPLT tell it MN110 (MACRO x); SWT19 (x=1); > SWH18 (program PF1 [with Macro 1]); MN255 (exit menu). > > That way, you long press the PFx button each time you want to go back and > forth. You can save the other PFx button for something else (I turn on and > off the ATU depending on the antenna I’m using). I will say this took a > couple of hours of experimenting with the KX3 and the macros. There was one > macro for which I was watching its output. The KX3 programming software was > very handy for this. > > Good luck. > > 73, > Joel - W4JBB > > > On Nov 28, 2014, at 7:16 PM, Randy Diddel <[email protected]> wrote: > > > > Good evening, night, day, etc. > > > > > > I have been working hard on getting my KX3 programmed to switch between > > voice and digital modes using a string of commands assigned to PF1 and > > PF2. I have them working perfectly except for setting VOX to ON for data > > modes. In the programmer's manual from Elecraft, it states that "A SET > > version of the command is planned." Has this been implemented? Does > > anyone know the syntax? > > > > For those interested here are the two strings: > > > > For Data: MD6;PA0;MG005;AG001;DT0;BW0400;PC12;PC015;ML000; > > For Voice: MD2;MG005;BW0240;SWH34;PA1;ML000;AG040;PC110;PA0; > > > > These really help out as I can be working JT65 and see a new one on the > > clusters, switch over, and jump in the side band pile up. VOX works best > > with WSJT-X and my specific configuration-that is why it would be good to > > have a bit to set it ON in the string listed above and a bit to switch it > > off when I switch to voice mode. > > > > > > 73 > > > > K5RHD > > > > /randy > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to [email protected] > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
