Hello Bill, A toggle should be easy at least in terms of programming. A set command with a 0 or 1 would be all it would take. The programmer's manual I have states one will be made available in the future. My question was if we were 'there yet' and does anyone know the syntax if it had.
73 /randy On Fri, Nov 28, 2014 at 10:56 PM, Nr4c <[email protected]> wrote: > VOX is a toggle. Don't think you can set a toggle button, only toggle it. > > Sent from my iPhone > ...nr4c. bill > > > > On Nov 28, 2014, at 11:54 PM, Randy Diddel <[email protected]> wrote: > > > > Hi Joel, > > > > I will look into doing just that. Still looking for an answer about VOX > > SET and if the command exists yet. > > > > Freeing up PF2 for the setup I use on SOTA would be a real bonus-I use a > > Heil Headset and usually have to manually set that up on the mountain. > > > > 73 > > > > K5RHD > > > > /randy > > > >> On Fri, Nov 28, 2014 at 8:09 PM, Joel Black <[email protected]> > wrote: > >> > >> Randy, > >> > >> If you wish, you can make them so each macro calls the other: one long > >> hold brings up the data mode; the second long hold brings up voice; > another > >> long hold brings up data; and so on. > >> > >> I don’t have my KX3 out at the moment, but here’s what my macro looks > like > >> going from CWSPLT to UNSPLT: > >> > >> CWSPLT - > MD3;SWT25;SWT25;FT1;SB1;UPB4;MN142;MP001;MN110;SWT27;SWH18;MN255; > >> UNSPLT - SB0;FR0;MN142;MP000;MN110;SWT19;SWH18;MN255; > >> > >> The last four commands of CWSPLT tell it MN110 (MACRO x); SWT27 (x=2); > >> SWH18 (program PF1 [with Macro 2 {from SWT27 where x=2}]); MN255 (exit > >> menu). > >> > >> The last four commands of UNSPLT tell it MN110 (MACRO x); SWT19 (x=1); > >> SWH18 (program PF1 [with Macro 1]); MN255 (exit menu). > >> > >> That way, you long press the PFx button each time you want to go back > and > >> forth. You can save the other PFx button for something else (I turn on > and > >> off the ATU depending on the antenna I’m using). I will say this took a > >> couple of hours of experimenting with the KX3 and the macros. There was > one > >> macro for which I was watching its output. The KX3 programming software > was > >> very handy for this. > >> > >> Good luck. > >> > >> 73, > >> Joel - W4JBB > >> > >>> On Nov 28, 2014, at 7:16 PM, Randy Diddel <[email protected]> wrote: > >>> > >>> Good evening, night, day, etc. > >>> > >>> > >>> I have been working hard on getting my KX3 programmed to switch between > >>> voice and digital modes using a string of commands assigned to PF1 and > >>> PF2. I have them working perfectly except for setting VOX to ON for > data > >>> modes. In the programmer's manual from Elecraft, it states that "A SET > >>> version of the command is planned." Has this been implemented? Does > >>> anyone know the syntax? > >>> > >>> For those interested here are the two strings: > >>> > >>> For Data: MD6;PA0;MG005;AG001;DT0;BW0400;PC12;PC015;ML000; > >>> For Voice: MD2;MG005;BW0240;SWH34;PA1;ML000;AG040;PC110;PA0; > >>> > >>> These real > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
