Got it; thanks. I misunderstood the previous message. Ted, KN1CBR
On 2/14/15, 8:38 AM, "Jim's Desktop" <[email protected]> wrote: > I looked it over and the only reason you would have to remove the KRX3 >is if you had it installed but were only buying one KSYN3A. You must >have the same synthesizer installed for both receivers. If you just >change out the main receiver's synthesizer, you then must remove both >the old 2nd RX synthesizer AND the receiver or you will confuse the K3's >MPU and it won't work. That was the gist of the previous thread. > >Jim - W0EB > >------ Original Message ------ >From: "Ken K3IU" <[email protected]> >To: "Dauer, Edward" <[email protected]>; "[email protected]" ><[email protected]> >Sent: 2/14/2015 9:33:29 AM >Subject: Re: [Elecraft] KSYN3A - installation question > >>I believe that you should ne able to install both boards without >>removing the KRX3 >>73, Ken K3IU >>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ >>On 2/14/2015 10:03 AM, Dauer, Edward wrote: >>>First question that came to my mind when I saw the announcement was >>>whether the KRX3 had to be removed and reinstalled in order to replace >>>the >>>synths. I found installing the KRX3 exasperating when I assembled the >>>K3 >>>- success came on about the 12th try. >>> >>>My K3 is 100 miles from where I am right now, so I looked at the >>>photos in >>>the K3 assembly manual and those in the new synth instructions, from >>>which >>>it appears that the swap could be done without removing the KRX3. >>>Could >>>we confirm whether R&R is required? Message below says it is. >>> >>>If the sub does have to be R&R¹d, anyone have suggestions about how to >>>reinstall it without the major fuss I experienced? >>> >>> >>>Ted, KN1CBR >>> >>> >>>>------------------------------ >>>> >>>>Date: Fri, 13 Feb 2015 13:21:20 -0800 >>>>From: Richard Thorpe <[email protected]> >>>>To: Elecraft List <[email protected]> >>>>Subject: [Elecraft] More KSYN3A >>>>Message-ID: <[email protected]> >>>>Content-Type: text/plain; charset=utf-8 >>>> >>>>I talked to Elecraft and you must remove the second receiver not just >>>>unplug it and remove its ?old? synth board. . . . >>>> >>>>R Thorpe K6CG >>>> >>>>------------------------------ >>>______________________________________________________________ >>>Elecraft mailing list >>>Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>Help: http://mailman.qth.net/mmfaq.htm >>>Post: mailto:[email protected] >>> >>>This list hosted by: http://www.qsl.net >>>Please help support this email list: http://www.qsl.net/donate.html >>>Message delivered to [email protected] >>> >> >>______________________________________________________________ >>Elecraft mailing list >>Home: http://mailman.qth.net/mailman/listinfo/elecraft >>Help: http://mailman.qth.net/mmfaq.htm >>Post: mailto:[email protected] >> >>This list hosted by: http://www.qsl.net >>Please help support this email list: http://www.qsl.net/donate.html >>Message delivered to [email protected] > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
