The K3 does the heavy listing while decoding CW and it and the P3 should be the same. What you can't do is use the K3 Utility and the P3 to display code simultaneously. Cheers and 73, Fred KE7X Author of: “The Elecraft K3s and P3 – Getting the Most out from Your High Performance Station”. "The Portable Elecraft KX3 – Going for the Summit with the KX3 and KX3-2M/4M" “The Elecraft KX-Line – The Complete Station” “The Elecraft KPA500 and KAT500 – the K-Line Dream Station, 2nd. Ed.” Printed, coil bound copies of these are all available at www.elecraft.com PDF files available from www.ke7x.com
"The Elecraft K3 and P3, 3rd Edition – Incorporating the KXV3B and KIO3B" “The Elecraft KXPA100, PX3 and 2M/4M Transverters – Assembling the KX3-Line Station” “The Elecraft P3, SVGA, and TX Monitor” “Upgrading the Elecraft K3 with K3s Components – Bridging the Gap” Printed copies available at www.lulu.com and pdf from www.ke7x.com. Free guides at ke7x.com KPA500 and KAT500 Quick Set Up Guide http://www.ke7x.com/home/k-line-introduction-and-set-up-guide KAT500 and KXPA500 Tuner Operation http://www.ke7x.com/home/kat500-and-kxpa100-tuners ________________________________________ From: Elecraft <[email protected]> on behalf of Ron D'Eau Claire <[email protected]> Sent: Friday, November 13, 2015 2:56 PM To: 'paul ecker'; [email protected] Subject: Re: [Elecraft] P3 CW Decoding doesn't match K3 I believe the P3SVGA only reproduces whatever characters are on the VFO B display. The P3SVGA does not separately decode the CW. If you are not getting faithful copy of VFO B on the K3 to the P3, something is amiss in the station setup. Try disconnecting anything else from the P3/K3 combo that is connected to any of the data ports on the K3 or P3 and see if that clears it up. You can easily test the transfer by recording a data mode message at the K3 and playing it back with the K3 in TEST mode so you aren't transmitting. You should have perfect copy on the P3SVGA monitor. 73, Ron AC7AC -----Original Message----- From: Elecraft [mailto:[email protected]] On Behalf Of paul ecker via Elecraft Sent: Friday, November 13, 2015 1:40 PM To: [email protected] Subject: [Elecraft] P3 CW Decoding doesn't match K3 While copying the ARRL 20M CW broadcast I noticed that the decoding on the K3 is quite accurate as long as the signal does not fade. But while the K3 is decoding very well, the data display of cw text on the bottom of the SVGA display is no whereas close to the accuracy of the K3. Anyone else encountered this? I don't see any applicable options in the SVGA menu on the P3 menu. Paul Eckerkc2nyu ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
