Fred- I am not using the K3 Utility at all, just the P3.
73 Paul
From: "Cady, Fred" <[email protected]>
To: Ron D'Eau Claire <[email protected]>; 'paul ecker' <[email protected]>;
"[email protected]" <[email protected]>
Sent: Friday, November 13, 2015 5:23 PM
Subject: Re: [Elecraft] P3 CW Decoding doesn't match K3
The K3 does the heavy listing while decoding CW and it and the P3 should be the
same. What you can't do is use the K3 Utility and the P3 to display code
simultaneously.
Cheers and 73,
Fred KE7X
Author of:
“The Elecraft K3s and P3 – Getting the Most out from Your High Performance
Station”.
"The Portable Elecraft KX3 – Going for the Summit with the KX3 and KX3-2M/4M"
“The Elecraft KX-Line – The Complete Station”
“The Elecraft KPA500 and KAT500 – the K-Line Dream Station, 2nd. Ed.”
Printed, coil bound copies of these are all available at www.elecraft.com
PDF files available from www.ke7x.com
"The Elecraft K3 and P3, 3rd Edition – Incorporating the KXV3B and KIO3B"
“The Elecraft KXPA100, PX3 and 2M/4M Transverters – Assembling the KX3-Line
Station”
“The Elecraft P3, SVGA, and TX Monitor”
“Upgrading the Elecraft K3 with K3s Components – Bridging the Gap”
Printed copies available at www.lulu.com and pdf from www.ke7x.com.
Free guides at ke7x.com
KPA500 and KAT500 Quick Set Up Guide
http://www.ke7x.com/home/k-line-introduction-and-set-up-guide
KAT500 and KXPA500 Tuner Operation
http://www.ke7x.com/home/kat500-and-kxpa100-tuners
________________________________________
From: Elecraft <[email protected]> on behalf of Ron D'Eau Claire
<[email protected]>
Sent: Friday, November 13, 2015 2:56 PM
To: 'paul ecker'; [email protected]
Subject: Re: [Elecraft] P3 CW Decoding doesn't match K3
I believe the P3SVGA only reproduces whatever characters are on the VFO B
display. The P3SVGA does not separately decode the CW. If you are not getting
faithful copy of VFO B on the K3 to the P3, something is amiss in the station
setup.
Try disconnecting anything else from the P3/K3 combo that is connected to any
of the data ports on the K3 or P3 and see if that clears it up.
You can easily test the transfer by recording a data mode message at the K3 and
playing it back with the K3 in TEST mode so you aren't transmitting. You should
have perfect copy on the P3SVGA monitor.
73, Ron AC7AC
-----Original Message-----
From: Elecraft [mailto:[email protected]] On Behalf Of paul
ecker via Elecraft
Sent: Friday, November 13, 2015 1:40 PM
To: [email protected]
Subject: [Elecraft] P3 CW Decoding doesn't match K3
While copying the ARRL 20M CW broadcast I noticed that the decoding on the K3
is quite accurate as long as the signal does not fade. But while the K3 is
decoding very well, the data display of cw text on the bottom of the SVGA
display is no whereas close to the accuracy of the K3. Anyone else encountered
this? I don't see any applicable options in the SVGA menu on the P3 menu.
Paul Eckerkc2nyu
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
