Todd,
Was the K3 in receive or transmit mode when it went dead?
73,
Scott K9MA
On 5/16/2016 20:58, Richard Fjeld wrote:
I have seen breakers let go for no apparent reason. It seemed like it
was a mechanical failure in the breaker.
Dick, n0ce
On 5/16/2016 5:27 PM, Rick Bates (WA6NHC) wrote:
Is it possible that it 'belched' and the power reset is what really
fixed it?
73,
Rick WA6NHC
Tiny iPhone keypad, spell check happens
On May 16, 2016, at 1:40 PM, Todd Ruby <[email protected]> wrote:
Well Ron, I guess there's a first time for everything. Although the
radio was deaf and dumb, I had display function and it looked as it
normally does after turning on the power. There was just no receive
nor output power.
I turned it off, pressed the 20 amp circuit breaker on the rear
panel and sigs were coming through the headphones and I had full power.
Today it's also operating perfectly.
73
Todd
On May 16, 2016, at 3:30 PM, Ron D'Eau Claire <[email protected]> wrote:
Todd responded to me off the reflector that he lost all power to
the K3 so it wasn’t the 20A breaker. That only controls power to
the KPA3. The front panel is still powered and the receiver
continues to work.
I suggested it might be the self-resetting breaker inside the K3.
That will turn it off completely. Actually power will still be on
the KPA3 module and anything plugged into the 12V external power
connector on the K3 rear panel, but the K3 itself will look dead
with no front panel lights, receive or other functions until it
cools and resets itself.
I’ve never had an issue with either breaker opening unexpectedly.
73, Ron AC7AC
From: [email protected] [mailto:[email protected]]
Sent: Monday, May 16, 2016 12:18 PM
To: Ron D'Eau Claire; 'todd ruby'; 'Elecraft Reflector Reflector'
Subject: Re: [Elecraft] circuit breaker
I believe Todd is referring to the breaker on the K3, not his house
panel circuit?
Ron has some good advice, but I wonder how common this circuit
breaker operates?
I looked thru my manual for more info on it. The block diagram
shows it as a 25A fuse,
text and device indicate 20A circuit breaker, but NO info on the
type operating curve, or current vs. time for minimum trip?
I have a 10A circuit breaker on my 40Ahr battery supply and it has
never tripped. It is a thermal time delay like most house breakers.
Anyone out there have any clue? Wayne?
Mike AC5P
On Monday, May 16, 2016 12:28 PM, Ron D'Eau Claire <[email protected]>
wrote:
The normal underlying cause for the breaker to open is
over-current. That's
a 20A breaker that protects only the KPA3 100 watt amplifier
module. The
first thing I'd do is check the current drain from your power
supply on the
band where you experienced the problem. First set the power to 10
watts so
the KPA3 is bypassed and note the total current drain key down. Now
crank up
the power and see if the part used by the KPA3 is pushing 20A. For
example,
if your total current at 10 W was 3A, does the total at 100 watts
approach
23A? IF so, the breaker was simply doing its job. Note that circuit
breakers
are not precision devices so it may trip a couple of amperes one
way or the
other from 20A.
A primary reason for excessive KPA3 current is a high SWR on your
antenna
system. The higher the SWR, the less efficient the KPA3 becomes and
the more
current it has to draw to produce the power.
A defective breaker can also start tripping at lower currents.
73, Ron AC7AC
-----Original Message-----
From: Elecraft [mailto:[email protected]] On Behalf
Of todd
ruby
Sent: Monday, May 16, 2016 9:08 AM
To: Elecraft Reflector Reflector
Subject: [Elecraft] circuit breaker
Would anyone venture to guess what would cause the circuit breaker
to trip
on a K3? Mine did all of a sudden yesterday. Fortunately, my friend
suggested the reset and voila, I am back on the air. But if there
is an
underlying cause, I think it would be wise to be aware of it so as to
preclude this episode from repeating. Any thoughts are welcome.
73
todd
WB2ZAB
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net/
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
--
Scott Ellington K9MA
Madison, Wisconsin, USA
[email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
