Alas, no mention of the K2, my FD go to radio. This is understandable,
and no criticism is meant. The K2 is yesterday's radio, while the KX2/3
are for today and tomorrow. That said, it's fun to run up a lot of CW
q's on the "old" K2 while other operators in the group are using
up-to-date Japanese radios and struggling with SSB.
...robert
On 06/25/2016 00:16, Wayne Burdick wrote:
Here are my annual tips for getting the most out of your rig at Field Day.
(Some are Elecraft-specific--thanks for the bandwidth!)
1. BATTERY LIFE: To conserve battery life, use hunt-and-pounce rather than
calling CQ, and use lower power output when possible. This is especially
practical on a very quiet band, such as on 15 or 10 meters in the afternoon and
early evening. You'll be amazed at how many stations you can work with one watt
when these higher bands are open.
- Lower power can also keep the rig cooler. (As will operating in the shade! At
least keep the heat sink in the shade, if you can. On the KX3, the heat sink
occupies the back edge and bottom of the enclosure. On the KX2, it's the right
side panel.)
- To reduce supply current in receive mode, use headphones rather than the
internal speaker, and if lighting conditions permit, turn off the LCD backlight
(MENU:BKLIGHT).
- The KX2 has an amp-hour monitoring feature. Tap DISP and rotate VFO B to
obtain this reading. To clear the AH value to zero, go into the AMP HRS menu
entry and hold CLR.
- The KX3 automatically switches the power amplifier to a more efficient setting based on
the mode, supply voltage, and power setting. You can tell that power-saving mode is in
effect by a decimal point after the 'W' in the power value (e.g., "5.0 W."). In
SSB and audio data modes, the applicable level is 3.0 watts.
2. QRP HUNT-AND-POUNCE TIP: This type of operation can be greatly enhanced by
using dual watch (KX2/KX3) or a sub receiver (K3/K3S). It allows you to keep
one VFO on a station you're waiting to call, while tuning the other VFO to look
for the next station to call. (If you beat my own 1B-Battery score because of
this tip...guess I asked for it :)
3. ANTENNA SELECTION: The general rule is, "the longer and higher, the better,"
suggesting wire-in-a-tree antennas. (If you're lucky enough to have a portable yagi,
that's even better.)
- When winding antenna wire for storage, wind it in a figure-8 pattern. When
you release the bundle later, it will spring out easily without kinks or
tangles.
- An electrically short whip will work in a pinch, but you'll typically realize
a 5 to 15 dB improvement on both RX and TX with an an-hoc wire antenna.
- Most Elecraft rigs have an optional internal, wide-range ATU that can tune
random wire antennas on all or some bands. Once the antenna is set up, go into
the ATU menu entry on each band of interest and hold CLR to clear out all
L-network memories. You may then only have to do ATU TUNE once or twice per
band. Data for your home antennas may be stored for up to 32 smaller segments
on each band.
- When connecting a wire directly to an ATU, avoid wire lengths that are
multiples of a half-wave on any target band (unless you're using a half-wave
antenna with a matching transformer at the rig). 26' and 52' (approximately)
work well for 40-6 meters in most cases, and 52' will usually allow matching on
80 m as well.
- You can use these same lengths for counterpoise wires, which are essential
for low loss on transmit. Without at least one counterpoise wire, your
transmitted signal will be an additional 10-20 dB lower, even if the ATU can
match the antenna.
4. ANTENNA SPACING: If you're using more than one transmitter, try to keep the
antennas as far apart as possible and perpendicular to each other. This is a
good practice with all FD stations, because it can prevent receiver de-sensing
and intermodulation distortion. If two stations unavoidably have their antennas
in each other's near fields, you can dig into a pretty deep bag of tricks,
including reducing preamp gain or turning on the attenuator. These settings are
per-band on all Elecraft rigs.
- KX3: Try setting MENU:RX SHFT to 8.0 rather than NOR. (The KX2 always uses 8
kHz shift.)
5. OSCILLATOR ISOLATION: The KX2 and KX3, like other radios with a quadrature
direct-conversion architecture, use a VFO (local oscillator) running at or very
close to the operating frequency. If you have another radio on the same band as
the KX2 or KX3, and the antennas are close together, the other radio may be
able to hear the rig's oscillator when they're both tuned close to the same
frequency.
To prevent this entirely, the KX3 includes an isolation amplifier that keeps
the oscillator from radiating back through the mixer. Normally this amplifier
is turned off to save about 15 mA of receive-mode current drain. To turn on the
isolation amp, set MENU:RX ISO to ON. This has no effect on performance.
The KX2 doesn't have an isolation amp, but isolation is very good when the
preamp is on.
Have fun!
73,
Wayne
N6KR
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
--
Robert G Strickland, PhD ABPH - KE2WY
[email protected]
Syracuse, New York, USA
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
