That is interesting. I have my KPod powered from the K3 12v output so have been turning both off and on so haven't noticed the intermittents.
In any event, the KPod is great! Cheers, Fred ________________________________ From: Elecraft <[email protected]> on behalf of Marty Koszewski <[email protected]> Sent: Wednesday, November 23, 2016 12:42 PM To: [email protected] Subject: [Elecraft] K-Pod MCU 1.09 'F3 Power Up' Question Hi Fred, Thank you for your detailed response. I am able to get my K-Pod to behave as you described. However, the 'F3 power up' seems to work intermittently. I must cycle the radio and K-Pod to get the tuning rate change to take place. Re-powering the K-Pod only does not seem to consistently change the tuning rate. I am looking forward to the firmware upgrade that will allow the K-Pod to have the same tuning rate as the K3S (instead of 1:2 or 1:4). Happy Thanksgiving! Marty - N1VH ------------------------------------------------------------------------- Hello Marty, I don't remember seeing any response to your question so here is what I have found with my KPod: The K3's tuning rate is determined by VFO CTS, FST and CRS and there are two fine rates (1 Hz and 10 Hz) and a course rate (100 Hz) depending on the FINE/COARSE switch. So when my CTS is 200, the K3 tunes 200 Hz, 2 kHz and 10 kHz per revolution. The normal power-on KPod tunes 100 Hz, 1 kHz, and 5 kHz per revolution. (it divides by 2). Holding F3 when power-on the KPod tunes 50 Hz, 500 Hz and 2.5 kHz per revolution (divide by 4). Cheers, Fred KE7X For all KE7X Elecraft books, see www.ke7x.com<http://www.ke7x.com <http://www.ke7x.com/>> (A macro programming book is coming soon.) ________________________________ From: Elecraft <elecraft-bounces at mailman.qth.net <http://mailman.qth.net/mailman/listinfo/elecraft>> on behalf of Marty Koszewski <mtkoszew at gmail.com <http://mailman.qth.net/mailman/listinfo/elecraft>> Sent: Monday, November 21, 2016 3:18 PM To: elecraft at mailman.qth.net <http://mailman.qth.net/mailman/listinfo/elecraft> Subject: [Elecraft] K-Pod MCU 1.09 'F3 Power Up' Question I installed the latest K-Pod firmware - MCU 1.09. The release notes state "Adds a power-on feature: if the F3 button is held during power up the K-Pod encoder uses a divide by 4 scaling factor." I do not notice any difference when powering up holding the F3 button. What is the 'F3' power-up supposed to do? I thought it might address the 4X VFO knob speed difference between the K3 and the K-Pod (my K3s VFO is still 4X faster than the K-Pod). Thanks. Marty - N1VH ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft <http://mailman.qth.net/mailman/listinfo/elecraft> Help: http://mailman.qth.net/mmfaq.htm <http://mailman.qth.net/mmfaq.htm> Post: mailto:Elecraft at mailman.qth.net <http://mailman.qth.net/mailman/listinfo/elecraft> This list hosted by: http://www.qsl.net <http://www.qsl.net/> Please help support this email list: http://www.qsl.net/donate.html <http://www.qsl.net/donate.html> Message delivered to fcady at montana.edu <http://mailman.qth.net/mailman/listinfo/elecraft> ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
