I have a KX3 hooked to a SteppIR controller. All I had to do was create a Y cable to go from radio to the computer and the SteppIR controller. I hooked up to the SteppIRs Data In port (IIRC). The computer connection was for control of the KX3 (not the SteppIR). The KX3 was programmed to send out its frequency, the SteppIR setup to receive the Kenwood protocol and set for AutoTrack. When frequency changes, the SteppIR adjusts the antenna.
I could even run the this setup with the computer turned off and the SteppIR would change frequency right along with the rig. So no computer, no other controller, to have the KX3 control the SteppIR. Joe KO8V > On Dec 14, 2016, at 3:02 PM, W0MU Mike Fatchett <[email protected]> wrote: > > Even with a Y cable from SteppIR the controller only listens to the signals. > It does not ask for anything. So you have to have something that is sending > out polling data regularly, which is why you need the computer. > > Alternatively if you us a Microham controller there is a good chance you can > buy their Ilink cable and hook it into the SteppIR and you are set. The > Microham will also defeat you Xmitting while the antenna is moving. > > W0MU > > > On 12/14/2016 1:28 PM, Dick Dievendorff wrote: >> I googled "stepper y cable" and found these. Maybe the other "hits" will be >> of use as well. >> >> http://www.steppir.com/wp-content/uploads/2011/10/Y-Cable.pdf >> >> http://www.steppir.com/wp-content/uploads/2011/10/Transceiver-Interface-Operation-5-28-09.pdf >> >> Have fun! >> >> 73 de Dick, K6KR >> >> >> >> >> -----Original Message----- >> From: Elecraft [mailto:[email protected]] On Behalf Of >> Jean-François Ménard >> Sent: Wednesday, December 14, 2016 11:57 >> To: [email protected] >> Subject: [Elecraft] SteppIR controller with K3S+P3 >> >> Hi everyone! >> >> I am a happy new owner of a brand new K3S and a P3, and everything is >> working quite well. >> >> Now, I would like to connect my SteppIR SDA-100 antenna controller to the >> K3S. I would like to be able to not use the computer to control the antenna >> controller. >> >> Any suggestion from a few hams with similar setup as mine on how to use the >> SDA-100 without the needs of a computer? >> >> My guess is I should do a Y cable between the connector labeled PC behind >> the P3 by using only the PIN 2 and 5 then thru the SDA-100 ??? >> >> 73 de Jeff | VA2SS >> >> __________________________________________ >> Jeff | VA2SS >> Jean-François Ménard >> >> [email protected] <mailto:[email protected]> >> www.VA2SS.com <http://www.va2ss.com/> >> >> Message envoyé à partir de mon appareil mobile. >> Message sent from my portable device. >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html Message >> delivered to [email protected] >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [email protected] > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
