Hi Steve,
I have the same problem with inadequate audio from my sound card when I use the rear panel Line In connector. But it works great if I use the front panel microphone connector. 73 Frank W3LPL ----- Original Message ----- From: "Steve Lund" <[email protected]> Cc: [email protected] Sent: Tuesday, December 5, 2017 11:06:14 PM Subject: Re: [Elecraft] K3 and WSJT-X Split operation. I have to run my K3 (S/N 1260) in split mode for WSJT-X. It works fine for tone frequencies above 1500 Hz, but for low (<1000 Hz) tones I can't get the ALC above a few bars with all controls (windows, wsjt-x, K3) to their maximum settings. Split 'solved' the problem, so I haven't investigated what is causing the low frequency roll off. Steve, K6UM On Tue, Dec 5, 2017 at 6:11 PM, Christopher Hoover <[email protected]> wrote: > I second Carl's explanation. > > I run WSJT-X on my K3s in rig split mode exclusively. It works > transparently and flawlessly. > > > On Mon, Dec 4, 2017 at 5:02 PM, Carl Clawson <[email protected]> wrote: > > > Hi Dany. This scared me a little bit too until I figured out what it was > > for. > > > > This is not just for expeditions. It's for everyone to use whose rig can > > handle it. > > > > Your TX frequency will still be as indicated on the FT8 screen. The > > software will raise the audio tone frequency by the same amount that it > > drops your VFO B so that your tone is in the right place. By doing this, > > the audio tone frequency is kept high enough that its harmonics will be > out > > of your FT8 passband. This is good -- it helps keep the band clean. > > > > See section 4.2 in the wsjt-x user guide. > > > > 73, Carl WS7L > > > > > > On Mon, Dec 4, 2017 at 3:59 PM, Dany VE2EBK <[email protected]> wrote: > > > > > Hi > > > > > > I would like to know if someone tried to run WSJT-X FT-8 in Split > mode, > > > not Split in the audio band but in real Split by activating the option > in > > > the radio tab of the configuration? > > > > > > Here, when I activate Split option, K3 change for Split, RX stay on VFO > > A, > > > TX change to VFO B but TX frequency drop of 1 kHZ ! If I turn the VFO > B > > > (TX) 3 kHz up for example, the VFO B return 1 KHz down when a > > transmission > > > start (TUNE is enough). > > > > > > This option seems to have been for the DX station rather than for use. > > > > > > It would be nice to check this before the 3Y0Z DXpedition that during > > ... > > > > > > 73 > > > > > > Dany VE2EBK > > > > > > ______________________________________________________________ > > > Elecraft mailing list > > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > > Help: http://mailman.qth.net/mmfaq.htm > > > Post: mailto:[email protected] > > > > > > This list hosted by: http://www.qsl.net > > > Please help support this email list: http://www.qsl.net/donate.html > > > Message delivered to [email protected] > > > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to [email protected] > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
