Reminds me of my first chain saw - I bought a demo, already assembled,
and it didn't cut for beans! Finally noticed the chain was on backwards.
George, W3HBM
On 4/28/2018 8:08 PM, rich hurd WC3T wrote:
At the risk of spinning this off topic, I am reminded of the lesson I
learned years ago when I drilled a through hole through the foundation for
our low voltage walkway wiring.
I wondered at the efficacy of my brand new shiny Dewalt hammer drill
because it was taking me freaking hours to go a few inches through the
concrete. After a couple of these tortuous hours, I cursed and looked
closely at the drill - and noticed that the direction switch was on
"reverse". Attention to detail is important in any endeavor.
On Sat, Apr 28, 2018 at 19:55 Don Wilhelm <[email protected]> wrote:
Ted,
The routing of the 240 volt wiring is a discussion between you and the
electrician - but there is always "a way" - even if that means drilling
through concrete (not nice, but possible).
Unless the wiring route is short, take Jim Beown's (K9YC) advice about
conductor sizes. Large conductors are not required for the current
draw, but oversize wire will help reduce the voltage drop when current
is drawn.
Putting all shack receptacles on a dedicated circuit for both 240 volts
and 120 volts AC will help a lot with received noise in your receiver,
and will isolate your shack powering from other circuits in the house.
K9YC gives good advice on this subject, even though your electrician may
consider it overkill for Jim's recommended wire size.
73,
Don W3FPR
On 4/28/2018 2:08 PM, Dauer, Edward wrote:
Placing both PS and amp where the 220 VAC outlet is accessible is
possible; but then I wouldn't be able to see the amp while operating, which
I would like to do. Wouldn't feel comfortable with a 1500 watt amp running
way out of sight. It would also then be in the kitchen on a floor above.
Not aesthetically the best that way, either.
As I described in reply to one other suggestion:
The "shack" is a spare bedroom in the lowest (of three) level of the
house, which because it is built into a hillside and therefore half of it
is below grade, has 12 inch concrete walls and a six inch (as I remember
it) concrete floor covered only with a carpet and carpet pad. The ceiling
of that room is finished as is the entire interior. The problem with
snaking a line through the walls from the distribution box which is on a
deck above ground level is that the entire space between the inside side of
the concrete and the drywall is filled with cellular foam insulation. It
was, when we had it built, the recommended way to go for the mountain
climate. I did think to have a conduit put through the wall to allow
antenna feedline coax to go through; but the electrician who was there said
there is now no way to get a 220 line through the walls without major
destruction. I might bring it overhead (between the finished ceiling of
the lower level and the floor of the next lev
el up) but then to get it down to a usable level in the "shack" would
require a conduit running down the inside wall surface. That may be what I
will have to do . . .
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
