Did you try without the “delays”? Is it so hard to start wsjt-x and select the 6M frequency in the drop- down box, and then adjust the P3?
And with the full spectrogram from wsjt-x , I don’t pay much attention to the O3. Sent from my iPhone ...nr4c. bill > On Jul 2, 2018, at 8:41 PM, Byron Peebles <[email protected]> wrote: > > I am having trouble with the following Macro on a K3S and P3/SVGA. > > BN10;DE500;MD6;DE100;FA00050313000;DE100;#CTF+00050315000;DE100;#SPN000043;DE100; > > The delays are just there to slow things down, right? No impact otherwise. > > What happens is the Macro executes, but when it completes, the P3/SVGA > switches the Center Frequency back to the previous band and the band the > radio is on is correct but the SVGA display differs from the P3 itself by > quite a bit. For specifics, I test the Macro by switching to 28MHz band. > After execution, the P3 shows the 28MHz center frequency but the SVGA shows > 74Mhz, or thereabouts. - If I change the SPN, the center frequency varies. > Suspicious. > > What I am trying to accomplish is this: > > Change bands(6m), Set Mode(Data), Set VFO-A Frequency (50313), Set P3 Center > (50315) and P3 Span (4.3) > > The idea is to have the audio bandwidth of FT-8 on the SVGA display (in this > example). > > What obvious mistake am I missing and forgetting? Thank you. > > 73, Byron > > Note the results are the same whether in a Macro button or some the test > command line. The results are fine when the command is broken up. I do know > about delays in command execution, especially band changes, and it does work > better when you are already on the band. > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] am having trouble with the following > Macro on a K3S and P3/SVGA. > > BN10;DE500;MD6;DE100;FA00050313000;DE100;#CTF+00050315000;DE100;#SPN000043;DE100; > > The delays are just there to slow things down, right? No impact otherwise. > > What happens is the Macro executes, but when it completes, the P3/SVGA > switches the Center Frequency back to the previous band and the band the > radio is on is correct but the SVGA display differs from the P3 itself by > quite a bit. For specifics, I test the Macro by switching to 28MHz band. > After execution, the P3 shows the 28MHz center frequency but the SVGA shows > 74Mhz, or thereabouts. - If I change the SPN, the center frequency varies. > Suspicious. > > What I am trying to accomplish is this: > > Change bands(6m), Set Mode(Data), Set VFO-A Frequency (50313), Set P3 Center > (50315) and P3 Span (4.3) > > The idea is to have the audio bandwidth of FT-8 on the SVGA display (in this > example). > > What obvious mistake am I missing and forgetting? Thank you. > > 73, Byron > > Note the results are the same whether in a Macro button or some the test > command line. The results are fine when the command is broken up. I do know > about delays in command execution, especially band changes, and it does work > better when you are already on the band. > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
