Sorry - spell check strikes again: 2. From J1 on the Main KSYN3A board to REF IN on the K144XV with Reference Oscillator Phase Lock Option installed.
John > On Jul 14, 2018, at 10:51 AM, John Stengrevics <[email protected]> > wrote: > > Hi Glenn, > > I had problems with this as well. I asked tech support and they sent an > email showing the following correct cable placement: > > 1. From J2 on KREF3 board to J83 on the Main KSYN3A board. > > 2. From J1 on the Main KSYN3A board to REF I note K144XV with Reference > Oscillator Phase Lock Option Installed. > > Hope this is helpful. > > John > WA1EAZ > >> On Jul 14, 2018, at 10:41 AM, WA7SPY <[email protected]> wrote: >> >> I have a new K3S kit and P3 kit that I put together. The following options >> are installed: >> FL1 - 13khz FM filter >> FL2 - 2.7 khz filter >> FL3 - 400 hz filter >> FL3 - 200 hz filter >> KPA3A 100 watt PA >> KAT3A 100 watt Tuner >> KBPF3A General coverage band pass >> KTCX03-1 High stability TCXO >> K144XV internal 2 meter module >> K3EXREF external 10mhz reference >> K144XV phase lock board. >> The K3S and options are all working. I had a problem with 2meters being off >> frequency after adding the K3EXREF and the K144XV reference board. I did a >> complete reset to factory defaults. I removed the K144XV reference board. >> Then set the 2 meter offset back to what was labeled on the module. The 2 >> meter frequency was accurate. I put the K144XV reference board back in. Now >> the 2 meter frequency is accurate with the board back in. My question is >> where is the TMP cable suppose to be connected on the KSYN3 board? I have >> one end connected to REF IN on the 2 meter module. I initially connected the >> other end to J4 on the KSYN3. I now have it connected to J1 on the KSYN3 do >> I have the TMP cable connected correctly? The documentation is a little >> confusing to me. Figure 13 page 15 on the K3EXREF manual shows J4 being used >> on the KSYN3A if both the KXV144 reference board and the KEXREF options are >> installed. There is an Errata sheet showing to use J1 on the KSYN3 board. >> Which one is c > or >> rect to use for my set up J1 or J4? >> The K3EXREF is working with very accurate frequency on the HF bands with my >> GPS 10 MHz disciplined oscillator clock connected. The 2 meter frequency >> was off when connected to J4. I am not sure if it was corrupt software and >> doing the reset corrected the issue and am uncertain where to connect to on >> the KSYN3A board? >> >> Thanks for any help, >> Glenn Maclean WA7SPY >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [email protected] > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
