Dave, I misunderstood your post. The per band settings I already understand, I thought you had a command to put the KPA1500 into standby mode from the KPOD and to change power levels from there.
73, Bill K9YEQ https://wrj-tech.com/ -----Original Message----- From: [email protected] <[email protected]> On Behalf Of David Box Sent: Tuesday, June 26, 2018 12:22 PM To: [email protected] Subject: Re: [Elecraft] KPOD Bill In the CONFIG setting on K3 go to PWR SET and set it to PEr bAnd. Then make sure you adjust your power level on the K3 with the KPA1500 in STBY and then adjust again with the KPA1500 in OPER. Do this for each band, then the K3 will automatically switch power levels based on the status of the KPA1500. Dave K5MWR On 6/26/2018 11:31 AM, Bill Johnson wrote: > Don, What command do you use for the KPA1500 power switching. Call me lazy > for asking. I use my KPOD for band changes, mode changes and tuning, fine, > coarse etc. Oh, I also use for Diversity, plus a switch to normalize > operation, for when I screw up. > > 73, > Bill > K9YEQ > > https://wrj-tech.com/ > > -----Original Message----- > From: [email protected] > <[email protected]> On Behalf Of Don Butler > Sent: Monday, June 25, 2018 11:30 PM > To: Edward <[email protected]>; [email protected] > Subject: Re: [Elecraft] KPOD > > I bought two KPODs right away Ed. I’m a DXer and have always enjoyed > busting pileups … especially the big ones that take up lots of bandwidth. > IMHO the K3 VFO B knob has always been rather klunky …. Doesn’t spin easily…. > Small, etc… so has always been awkward to use it while searching through a > large split pileup while trying to find the station the DX is calling….. so I > use the KPOD to tune VFO B most of the time…. And it works great …. The P3 > and Subreceiver are also really great tools for the big pileups. I use the > programmable KPOD buttons a lot …. A few for sending recorded DVR messages > (both CW and SSB) …. And others for switching A/B, A>B, Split +2, Split +5, > Split/Unsplit, Subreceiver on/off …. And switching power between 100W and 30W > (for driving the amp) …. Now that I have a KPA1500 which can do the drive > power switching for me when I go between operate and standby there’s no need > for the power switching anymore … > > I love my KPODs > > Don, N5LZ > > Sent from Mail for Windows 10 > > From: Edward via Elecraft > Sent: Monday, June 25, 2018 10:11 PM > To: [email protected] > Subject: [Elecraft] KPOD > > Is anybody using the KPOD and if so, seeing it’s benefit? > > 73, > Ed NI6S > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > [email protected] > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > [email protected] > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
