I will try this in the K3 Utility to see if I can get it to work there. - 73 and good DX de Mike, K6MKF, Past President - NCDXC
> -----Original Message----- > From: Tom <[email protected]> > Sent: Wednesday, July 25, 2018 10:47 AM > To: Mike Flowers <[email protected]>; 'W1IE' > <[email protected]> > Cc: [email protected] > Subject: Re: [Elecraft] I need some help with this string of macro commands > > Hi, > I tried this out as a Macro in Win4K3Suite and it works fine on the first > press. > By default, Win4K3 does not add any delay between each command when using > macros. > I think that this is a specific issue to DXlab. > 73 Tom > va2fsq.com > > > -----Original Message----- > From: Mike Flowers > Sent: Wednesday, July 25, 2018 12:38 PM > To: 'W1IE' > Cc: [email protected] > Subject: Re: [Elecraft] I need some help with this string of macro commands > > Hi Jerry, > > Thanks. I checked and I did not have the latest K3 programming manual which > contained the DE construct. However, still no joy in Muddville. > > Can not yet figure why the macro must be executed twice in order for the P3 > commands to be effective. > > - 73 and good DX de Mike, K6MKF, Past President - NCDXC > > > -----Original Message----- > > From: W1IE <[email protected]> > > Sent: Wednesday, July 25, 2018 4:09 AM > > To: 'Mike Flowers' <[email protected]> > > Subject: RE: [Elecraft] I need some help with this string of macro > > commands > > > > GM Mike, > > > > The command is "DE<value up to 250 - which represents milliseconds in > > delay> > > > > Example DE001 = a delay of 1 millisecond. I use this a lot on some of > > my N1MM scripts. Just to give the Elecraft K3 a "moment to breathe". > > Most helpful when I am sending multiple Tap or Holds commands. > > > > > > > > > > Hope this helps > > > > Best regards, > > > > Jerry, W1IE > > > > -----Original Message----- > > From: Mike Flowers <[email protected]> > > Sent: Tuesday, July 24, 2018 7:04 PM > > To: W1IE <[email protected]> > > Subject: Re: [Elecraft] I need some help with this string of macro > > commands > > > > Hi Jerry, > > > > I’ve search in vain for the delay macro construct. Perhaps there is > > an update K3 Programmers Manual ... > > > > -- Mike Flowers, K6MKF, NCDXC - "It's about DX!" > > > > > On Jul 24, 2018, at 3:56 PM, W1IE <[email protected]> wrote: > > > > > > GM Mike, > > > > > > Sometimes I have found that you need a delay in the command string. > > > This is so the Elecraft stuff can process some of the commands > > > before finishing the rest of the command. It seems, so I have been > > > told, that the entire line sent all at once and by the time Elecraft > > > gets to a particular command, it is already gone. > > > > > > The command for the delay is relatively new and I have forgotten > > > what it was. > > > > > > Best regards, > > > > > > Jerry > > > > > > > > > -----Original Message----- > > > From: [email protected] > > > <[email protected]> On Behalf Of Mike Flowers > > > Sent: Tuesday, July 24, 2018 11:10 AM > > > To: [email protected] > > > Subject: [Elecraft] I need some help with this string of macro > > > commands > > > > > > Hi Gang, > > > > > > > > > > > > Time to consult the brain trust, because my brain is getting tired . > > > > > > > > > > > > I am working on this macro string for use in DXLab to set the K3 and > > > P3 for 17M PSK operations. > > > > > > > > > > > > So, it's designed to: > > > > > > > > > > > > 1. Turn off the VOX > > > 2. Set MODE to DATA, data mode to DATA A > > > 3. Set LINE IN > > > 4. Mic (Line) Gain to 3 > > > 5. Monitor Level to 3 > > > 6. Then set the P3's center frequency to 18101.50 kHz with a SPAN of > > > 4 > > > > > > > > > > > > > > > VX0;MD6;DT0;XF2;MN255;MN053;UP;UP;MG003;ML003;MN255;#CTF+0001810 > > 1500;# > > > SPN000 > > > 040;MN255; > > > > > > > > > > > > The macro as written performs Steps 1 - 5 on its first execution but > > > will only perform Step 6 - the P3 commands - on the second execution. > > > > > > > > > > > > After the first execution, the center frequency on the P3 shows what > > > appears to be a random frequency, and the correct frequency is only > > > shown on > > the > > > second execution of this macro. I think there is some band stack > > > effect or > > > something going on but the command set for the P3 is limited. > > > > > > > > > > > > It's no burden to click the button twice, but I'd like to understand > > > why all these commands cannot be executed with one execution of the > > > macro > > string. > > > > > > > > > > > > Thank you for your help! > > > > > > > > > > > > - 73 and good DX de Mike, <http://www.qrz.com/db/k6mkf/> K6MKF, > > > Past President - <http://ncdxc.org/index.html> NCDXC > > > > > > > > > > > > ______________________________________________________________ > > > Elecraft mailing list > > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > > Help: http://mailman.qth.net/mmfaq.htm > > > Post: mailto:[email protected] > > > > > > This list hosted by: http://www.qsl.net Please help support this > > > email > > > list: http://www.qsl.net/donate.html Message delivered to > > > [email protected] > > > > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html Message > delivered to [email protected] > > > --- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
