The link was wrapped and broken in the middle. Put the two bits back together. You’ll get this, unless it gets broken again.
http://elecraft.365791.n2.nabble.com/K3EXREF-What-am-I-doing-wrong-td7614721.html wunder K6WRU Walter Underwood CM87wj http://observer.wunderwood.org/ (my blog) > On Aug 4, 2018, at 5:47 PM, hawley, charles j jr <[email protected]> > wrote: > > Bad link... > > Chuck Jack > KE9UW > > Sent from my iPhone, cjack > >> On Aug 4, 2018, at 7:06 PM, Gary Smith <[email protected]> wrote: >> >> I do not know why it was working a few >> days back and not working now but I found >> the answer revealed on this web page: >> >> http://elecraft.365791.n2.nabble.com/K3EXR >> EF-What-am-I-doing-wrong-td7614721.html >> >> It is stated in an addendum that when in >> REF CAL & you have the external 10 MHz >> source connected, you have to press 2 on >> the keypad to enable XREF IN. >> >> By doing so the asterisk started in about >> 10 seconds and all is well, the radio is >> again properly maintaining the frequency. >> No idea what made this function stop but >> this is what it took to start it again. >> >> 73, >> >> Gary >> KA1J >> >> >>> I have the K3EXREF installed in this K3. I >>> noticed when I clicked on a signal with >>> the P3 & marker, the signal was off a tad >>> from where it should be. On a hunch I >>> checked REF CAL and the asterisk was >>> missing. I know REF CAL had the flashing >>> asterisk a few days ago. >>> >>> I measured the signal coming from the >>> GPSDO and it was 10.000 0 MHz according to >>> the MFJ analyzer. I had recently put in >>> filters in the K3, a KXV3B and a KIO3B and >>> thought I might have dislodged a coax in >>> the K3 so I assured the integrity of all >>> the coax cables (I have the new synth >>> board). I also assured the K3EXREF was >>> seated properly and there were no obvious >>> loose components. I cannot get the >>> asterisk to flash and the board to lock >>> with the 10 MHz signal. >>> >>> I had to manually calibrate to WWV and it >>> was quite off.Does anyone have a >>> suggestion for me to try and get this to >>> sync? I re-read the K3EXREF installation >>> instructions and the board is nicely in >>> place, reloading known good configurations >>> with the K3 utility made no change. >>> >>> Either I borked a setting somewhere in >>> config or I have a failed component. >>> >>> Anyone have this issue before & found a >>> resolution? >>> >>> Thanks. >>> >>> 73, >>> >>> Gary >>> KA1J >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:[email protected] >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to [email protected] >>> >> >> >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [email protected] > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
