Kevin, I think going to the FLDIGI reflector is your best bet. It is good to know it is a FLDIGI issue and not a hardware issue. Sorry I couldn’t be more help. Good luck finding the fix and please let us know here on the Elecraft reflector what you find.
73, Mark, WB9CIF From: Kevin, N4TT <[email protected]> Sent: Thursday, July 18, 2019 02:45 To: Mark Musick <[email protected]> Cc: Elecraft Reflector Reflector <[email protected]> Subject: Re: [Elecraft] FSK-D, Y-BOX & WinKeyer - config help please Hi Mark... I'm sure you're right that it is something Fldigi is sending but it is not part of the macro. It's the same macro I use with AFSK (and CW). It seems to only happen when the macro contains <RX> which is supposed to put the rig back into receive at the end of the macro. If I send the same macro without <RX> then there are no additional characters sent. I'll probably head over to the fldigi forum soon and see what's said there. Kev On Wed, Jul 17, 2019 at 10:39 PM Mark Musick <[email protected]<mailto:[email protected]>> wrote: Hi Kevin, I don't use FLDIGI, but I can tell you what you are seeing is not a hardware issue. The reason your seeing TT N4TT PSE K is because that is what FLDIGI is sending. You need to look at the setup in FLDIGI. Is there a message that has TT N4TT PSE K that is chained to the message you created? Look in the FLDIGI manual or help file your answer may be there. 73, Mark, WB9CIF -----Original Message----- From: [email protected]<mailto:[email protected]> <[email protected]<mailto:[email protected]>> On Behalf Of Kevin, N4TT Sent: Thursday, July 18, 2019 00:52 To: Elecraft Reflector Reflector <[email protected]<mailto:[email protected]>> Subject: [Elecraft] FSK-D, Y-BOX & WinKeyer - config help please I seem to be digging a deeper hole so it's time to come to the K3 experts again. I'm still trying to get FSK (not AFSK) to work. My setup is a K3s, Y-Box, WinKeyer and Fldigi. I think I have everything set up properly but something very strange is happening. My CQ string is: <TX> CQ CQ CQ de <MYCALL> <MYCALL> <MYCALL> CQ CQ CQ de <MYCALL> <MYCALL> <MYCALL> pse k <RX> What shows up on Fldigi when sending: CQ CQ CQ de N4TT N4TT N4TT CQ CQ CQ de N4TT N4TT N4TT pse k TT N4TT PSE K Note that last line. I don't know where it's coming from. And it is showing up because tones are still being generated. The tone stops right after PSE K (caps). I have another macro: <TX> <CALL> de <MYCALL> <MYCALL> kn <RX> It sends: de N4TT N4TT kn T KN The physical setup: WinKeyer PTT to Y-Box FSK-in (tied to Accy pin1) WinKeyer KEY1 to Y-Box PTT-in (tied to Accy pin 4) Radio is in DATA FSK-D 45 bps. I'm not sure what else to try. 73, Kevin N4TT ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected]<mailto:[email protected]> This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]<mailto:[email protected]> ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
