OK, I have to admit that I just went back and tried it again and it does work as it should. This morning I could make it stop working just by switching the mode from DATA A to AFSK A. This afternoon it seems to make no difference which is selected, they both work and with VOX. Nice to know if I ever need it, but I will continue to use FSK when in RTTY mode. After all these decades I am just more comfortable with it and it only takes 1 com port per "radio" running SO2V. And I know Win 10 can't mess up the levels if I don't use any. Notebook when portable might get this treatment though.
On Sat, Mar 21, 2020 at 12:38 PM M. George <[email protected]> wrote: > Joe, I can confirm the same success for using AFSK A with VOX to key the > radio... and just for kicks and giggles... I have a K3S and a K3, the K3 > has the KIO3B install and I tested the AFSK A setup with MMTTY and N1MM on > both radios. *The conjecture / reports that it only works on a K3S is a > total red herring as Wes and Rich have reported? Wow that is a tangent for > sure...* They (K3S/K3 with the USB KIO3B) work exactly the same gents, > there is nothing magical about the K3S. I actually made a quick and dirty > YouTube video for you (Joe N9OK) and I'll send you the link to the video as > soon as it's published. It walks you would a setup for AFSK A direct with > MMTTY and shows a test... and shows you all the configuration screens so > you can pause the video and compare to your setup. I then reference that > instance of MMTTY in N1MM and show the setup there.... and I work some > stations... all using AFSK A on a K3 with the the KIO3B using VOX to key > the radio. It's a March miracle. > > Max NG7M > > On Sat, Mar 21, 2020 at 10:57 AM Richard Ferch <[email protected]> wrote: > > > Like Wes, I have an original K3 which I have been using in AFSK-A for > > years. I use N1MM+ with either MMTTY or 2Tone as the RTTY "engine". A few > > months ago I installed the KIO3B upgrade in my K3. After I installed the > > upgrade, AFSK-A RTTY worked right from the start using the USB audio > codec. > > I had no difficulties in getting it going. > > > > 73, > > Rich VE3KI > > > > N9OK wrote: > > > > Jim, > > > > Thank you very much for confirming that what I see isn't due to a broken > > K3. > > > > I agree that if firmware can fix this, it would be very nice. Elecraft > had > > this particular feature listed in the feature set for the upgrade, IIRC, > > which is a large reason I splurged on the upgrade. I didn't want any more > > external interface confusion. > > > > On to configuring for FSK and perhaps playing in BARTG a little. > > > > 73 Joe N9OK > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to [email protected] > > > > > -- > M. George > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] > -- Jim K0XU [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
