It is easy to cross thread nuts and screws this way. IME, machine threads...which is likely what you have here...either work or they don't. You should be able to get at least 2 clean, easy rotations. And that is for a nut that is going on a bolt/stud that will not stand proud of the nut when it is tight. That likely applies to many of the screws and nuts in the Elecraft equipment. Folks who "think" that they have a good match and that the nut just needs to be "tightened" wind up cross threading, and then you be lucky a) get the nut off, and b) get the correct one to fit. This works for all sizes...right up to, and past, engine block studs and nuts. (Experience.) Many are the times that I have wrapped my hand around a manifold, to a stud I can't see, and gently rotated the nut until I was sure that I had a proper fit.
Now...back to the KX3...this comes as a kit, yes? Then perhaps the kit manual calls out the nut size. On 2020-08-28 13:34:-0700, Mooneer Salem wrote: >Tried some normal 1/4"-20 hex nuts from Lowe's too (much too thick mind you, >but should at least confirm if the diameter/TPI are correct) and no such >luck.� > >Interestingly, I took off the nut from a spare SMA pigtail and it was able to >mate it with the microphone connector. However, I couldn't rotate it past 1/2 >turn or so and I didn't want to force it with tools and potentially damage the >jack. If it was the correct size, I'd have been able to tighten it much >further by hand, right? > >-Mooneer K6AQ > >On Fri, Aug 28, 2020 at 1:21 PM hawley, charles j jr ><<mailto:[email protected]>[email protected]> wrote: >1/4"-20� I think > >Chuck Hawley >� <mailto:[email protected]>[email protected] >� >� Amateur Radio, KE9UW >� aka Jack, BMW Motorcycles� > > >---------- >From: ><mailto:[email protected]>[email protected] ><<mailto:[email protected]>[email protected]> on >behalf of Mooneer Salem <<mailto:[email protected]>[email protected]> >Sent: Friday, August 28, 2020 3:12 PM >To: Elecraft Reflector ><<mailto:[email protected]>[email protected]>; ><mailto:[email protected]>[email protected] ><<mailto:[email protected]>[email protected]> >Subject: [Elecraft] KX3 microphone nut size >� >Hi all, > >Does anyone know what exactly would replace the microphone nut on the KX3? >(I seem to have somehow misplaced mine.) The jack itself seemed to measure >1/4" OD but some 1/4"-32 panel nuts that I found don't seem to screw into >it. > >Thanks, > >-Mooneer K6AQ >______________________________________________________________ >Elecraft mailing list >Home: ><http://mailman.qth.net/mailman/listinfo/elecraft>http://mailman.qth.net/mailman/listinfo/elecraft >Help: <http://mailman.qth.net/mmfaq.htm>http://mailman.qth.net/mmfaq.htm >Post: <mailto:[email protected]>mailto:[email protected] > >This list hosted by: <http://www.qsl.net>http://www.qsl.net >Please help support this email list: ><http://www.qsl.net/donate.html>http://www.qsl.net/donate.html >Message delivered to <mailto:[email protected]>[email protected] > >_._,_._,_ > >---------- >Groups.io Links: > >You receive all messages sent to this group. > ><https://groups.io/g/Elecraft-KX/message/67316>View/Reply Online (#67316) | ><mailto:[email protected]?subject=Re:%20Re%3A%20%5BElecraft-KX%5D%20%5BElecraft%5D%20KX3%20microphone%20nut%20size>Reply > To Group | ><mailto:[email protected]?subject=Private:%20Re:%20Re%3A%20%5BElecraft-KX%5D%20%5BElecraft%5D%20KX3%20microphone%20nut%20size>Reply > To Sender | <https://groups.io/mt/76482569/912264>Mute This Topic | ><https://groups.io/g/Elecraft-KX/post>New Topic > ><https://groups.io/g/Elecraft-KX/editsub/912264>Your Subscription | ><mailto:[email protected]>Contact Group Owner | ><https://groups.io/g/Elecraft-KX/leave/8570097/71366771/xyzzy>Unsubscribe >[[email protected]] >_._,_._,_ ~R~ 72/73 de Rich NE1EE On the banks of the Piscataqua
______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
