Hi Henk, nothing visible, but R79 was 700 Ohm instead of 10k. Found a THT 10kOhm and fortunately, there is enough space for this big resistor.
Now working like hell :-) Many thanks! 73s Chris DL1MGB Am 24.04.2021 um 10:48 schrieb [email protected]: > Hi Chris, > > Check if R78 and R79 are still OK. > If the encoder does not get voltage(s) via these resistors if will never > work. > 73 Henk > PA0C > > -----Oorspronkelijk bericht----- > Van: [email protected] <[email protected]> > Namens Christian Janssen DL1MGB > Verzonden: zaterdag 24 april 2021 09:53 > Aan: [email protected] > Onderwerp: Re: [Elecraft] K3 RIT not working > > > > Am 24.04.2021 um 09:52 schrieb Christian Janssen DL1MGB: >> Hi Gernit, >> >> maybe I was a bit unclear. The RIT didn't work before I changed the > encoder. And it still doesn't work after I replaced the encoder by a brand > new one directly shipped from Elecraft. >> >> 73s Chris DL1MGB >> >> >> >> Am 24.04.2021 um 09:39 schrieb G: >>> Hi Chris >>> I had the same issue with the filter shift pot. I mailed elecraft support > and they sent me a replacement part. Takes some effort to replace it but it > is doable. >>> 73 Gernit DF5RF >>> >>> -- >>> Diese Nachricht wurde von meinem Android Mobiltelefon mit GMX Mail > gesendet. >>> Am 24.04.21, 07:38 schrieb Christian Janssen DL1MGB <[email protected]>: >>> >>> Hello, >>> >>> after doing some refurbishing (changing rotten connectors, > cleaning,...) I was curious if changing the RIT encoder will make the RIT > work again. But it doesn't. >>> >>> K3 #1532 >>> Firmware 5.67 >>> >>> I can press on the RIT and XIT button and it shows RIT and XIT in the > display, the green LED below the CLR goes on. But when I turn the RIT knob, > it stays at 0.00 and the frequency also doesn't change (also audibly). Also > when both RIT and XIT are OFF and CONFIG:VFO CRS is ON, then no coarse with > the RIT knob. >>> >>> Is there any hidden setting I missed? Or died just this RIT/XIT > function on the board? I also couldn't see any broken lines or parts around > the RIT encoder on the PCB. >>> >>> I am curious if there is easy help oout there. >>> >>> 73s Chris DL1MGB >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft > <http://mailman.qth.net/mailman/listinfo/elecraft> >>> Help: http://mailman.qth.net/mmfaq.htm > <http://mailman.qth.net/mmfaq.htm> >>> Post: mailto:[email protected] >>> >>> This list hosted by: http://www.qsl.net <http://www.qsl.net> >>> Please help support this email list: http://www.qsl.net/donate.html > <http://www.qsl.net/donate.html> >>> Message delivered to [email protected] >>> > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html Message > delivered to [email protected] > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
