> Not true of the KRC2 IF you are using the > AuxBus line. The question was specifically with respect to BCD output - not Aux Bus. Neither the microHAM Band Decoder not Station Master require any modification (or care about the BCD coding) if the serial (CAT) data is used for band decoding but that wasn't the question that Jan asked.
Another respondent mentioned an specific band decoding device from one vendor. My response was to provide the data about the other available products that Jan was likely to be using as well as get the full information into the archives so another person searching for the same information in two or three years from now was not left to wonder about compatibility with devices other than one specific product. 73, ... Joe, W4TV > -----Original Message----- > From: Greg - AB7R [mailto:[EMAIL PROTECTED] > Sent: Friday, December 05, 2008 11:30 AM > To: '' Jan Erik Holm ''; [email protected]; 'Joe; Subich; W4TV' > Subject: RE: [Elecraft] K3 Band Data > > > The Elecraft KRC-2 and >W9XT Band Decoders do not have > pull-up resistors and will >require the addition of 2.2 - > 10K resistors Not true of the KRC2 IF you are using the > AuxBus line. I have the K3 ACCY AuxBus connected to the KRC2 > and it works great. No changes needed. > ------------------------- 73, Greg - AB7R Whidbey Island WA > NA-065 On Fri Dec 5 7:37 , "Joe Subich, W4TV" sent: > > >The BCD encoding is the same as the FT-1000D/FT-2000. > > >Interfacing to a microHAM or TopTen Band Decoder requires > >no internal modification (both products include pull-up > >resistors on their BCD inputs). The Elecraft KRC-2 and > >W9XT Band Decoders do not have pull-up resistors and will > >require the addition of 2.2 - 10K resistors in the decoder > >or on the KIO3 board as documented in the Negative ALC >Mod > bulletin. > >73, > > ... Joe, W4TV > > > > >> > -----Original Message----- >> From: > [EMAIL PROTECTED] >> > [EMAIL PROTECTED]','','','')">elecraft-bounces > @mailman.qth.net] On Behalf Of Jan Erik Holm >> Sent: Friday, > December 05, 2008 4:00 AM >> To: Elecraft Reflector >> > Subject: [Elecraft] K3 Band Data >> >> >> Is the K3 band > data compatible with Yaesu (ex:FT1000D) >> BCD band data. > Looks to me that it is, or? >> >> 73 Jim SM2EKM >> >> > _______________________________________________ >> Elecraft > mailing list >> Post to: [email protected] >> You must > be a subscriber to post to the list. >> Subscriber Info > (Addr. Change, sub, unsub etc.): >> > http://mailman.qth.net/mailman/listinfo/elecraft >> >> > Help: http://mailman.qth.net/subscribers.htm >> Elecraft web > page: http://www.elecraft.com > > >_______________________________________________ >Elecraft > mailing list >Post to: [email protected] >You must be > a subscriber to post to the list. >Subscriber Info (Addr. > Change, sub, unsub etc.): > > http://mailman.qth.net/mailman/listinfo/elecraft > >Help: > http://mailman.qth.net/subscribers.htm >Elecraft web page: > http://www.elecraft.com > _______________________________________________ Elecraft mailing list Post to: [email protected] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
