> Is my DB37 cable incorrect? No, you simply have the very first version the factory built.
> -----Original Message----- > From: John Gaynard [mailto:[email protected]] > Sent: Monday, January 05, 2009 11:56 AM > To: [email protected] > Subject: RE: [Elecraft] K3 using Microham MKII > > > Joe > > Both Line-in/out plugs are stereo plugs on my K3 DB37 cable. > Line-in on the K3 specifies a mono input. Is my DB37 cable incorrect? > > John > > -----Original Message----- > From: Joe Subich, W4TV [mailto:[email protected]] > Sent: Monday, January 05, 2009 10:51 AM > To: 'John Gaynard' > Subject: RE: [Elecraft] K3 using Microham MKII > > > > > Are those the ones labeled PC-In PC-Out? > > Yes. Connect based on the "pigtail." BTW, you have the > original DB37-EL-K3 design. Those labels were based on > an early prototype picture that did not get corrected > in time <G>. > > 73, > > ... Joe, W4TV > > > > > -----Original Message----- > > From: John Gaynard [mailto:[email protected]] > > Sent: Monday, January 05, 2009 10:28 AM > > To: [email protected] > > Subject: RE: [Elecraft] K3 using Microham MKII > > > > > > Are those the ones labeled PC-In PC-Out? PC-In to Line-In > > on K3 PC-Out to Line-Out on K3. Those were the only > > connections confusing me mainly because of the PC-In/PC-Out label. > > > > -----Original Message----- > > From: Joe Subich, W4TV [mailto:[email protected]] > > Sent: Monday, January 05, 2009 2:14 AM > > To: 'John Gaynard' > > Subject: RE: [Elecraft] K3 using Microham MKII > > > > > > > > > What connections are required to run PSK with the Microham MKII > > > interfacing to the K3? Where to the audio cables on the > MK II DB37 > > > connect? > > > > Connect the cables as labeled to the ACC, RS-232, Line IN , > > Line Out, Key and mic jacks. On some early versions of > > the DB37-El-K3 cable set the Line In and Line Out plugs > > may be marked incorrectly - the Line Out jack has the > > "pigtail" with a separate 3.5mm female jack (Sub RX/Right > > audio out). > > > > > I do not see the > > > Microham soundcard listed on the Sony but I see the Line > > > light blinking on the MKII so I guess it sees the soundcard > > > but does not recognize it as Microham CODEC. > > > > Check in Windows device manager ... > > > > 73, > > > > ... Joe, W4TV > > > > > > > > > > > -----Original Message----- > > > From: [email protected] > > > [mailto:[email protected]] On Behalf Of > John Gaynard > > > Sent: Sunday, January 04, 2009 9:54 PM > > > To: [email protected] > > > Subject: [Elecraft] K3 using Microham MKII > > > > > > > > > What connections are required to run PSK with the Microham MKII > > > interfacing to the K3? Where to the audio cables on the > MK II DB37 > > > connect? I cannot find any info for connecting the MKII > to the K3 > > > in the Microkeyer II doc, or if it is there, I don't see > it. Also, > > > I am using one of the new Sony desktops VGC-LT35 and HRD current > > > release. I do not see the Microham soundcard listed on > the Sony but > > > I see the Line light blinking on the MKII so I guess it sees the > > > soundcard but does not recognize it as Microham CODEC. > > > > > > Worst case I'll put my old Sony laptop back to do PSK because it > > > sees the Microham CODEC soundcard for sure. > > > > > > John > > > > > > > > > > > > _______________________________________________ Elecraft mailing list Post to: [email protected] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
