> It seems a poor choice to try installing that resistor with > the Syn board in place when it's "hammer simple" to pull the > board and work on it properly.
The "Elecraft procedure" is easier written than done (I've fought with (and lost) the lockwashers more times that I care to). Running the cables and getting the KRX3 in place is also not the most simple/intuitive operation. It's certainly not a five minute job for me even though I've pulled and installed KRX3 several times between my two rigs. 73, ... Joe, W4TV > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Ron > D'Eau Claire > Sent: Saturday, August 01, 2009 7:20 PM > To: [email protected] > Subject: Re: [Elecraft] PL1 Error on 10M > > > It seems a poor choice to try installing that resistor with > the Syn board in place when it's "hammer simple" to pull the > board and work on it properly. > > See the Elecraft procedure at: > > http://www.elecraft.com/K3/mods/ELECRAFT_Application_Note_KSYN3_ALC_Rev_A.pdf > > 99% of the work is just getting the top cover off and putting > it back on. > > Ron AC7AC > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Bill W4ZV > Sent: Saturday, August 01, 2009 3:10 PM > To: [email protected] > Subject: Re: [Elecraft] PL1 Error on 10M > > > Regarding the Synthesizer ALC mod, **with care** the 180k > resistor(s) (plural if you have a KRX3) can be installed > without removing the synthesizer board(s). See #3 below. > > http://www.mail-archive.com/[email protected]/msg72210.html > > 73, Bill > > > > Evert Bakker (PA2KW) wrote: > > > > Hello Ralph, > > > > It is a known issue and can be solved easily. > > I'll send you the document directly (which is on the > Website as well). > > > > 73's, Evert PA2KW > > > > -----Original Message----- > > From: [email protected] > > [mailto:[email protected]] On Behalf Of Ralph > > Sent: Saturday, August 01, 2009 19:21 > > To: [email protected] > > Subject: [Elecraft] PL1 Error on 10M > > > > Only on 10M I get a PL1 error - PL1 * 7.5 - 10M inoperable just > > before NAQP too. Any odeas appreciated. > > > > Ralph K1ZZI > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > > > > > -- > View this message in context: > http://n2.nabble.com/PL1-Error-on-10M-tp3369887p3370806.html > Sent from the Elecraft mailing list archive at Nabble.com. > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
