Wayne Burdick wrote: > Dick, > > What version of HRD are you using? > > tnx > Wayne > > On Oct 9, 2009, at 3:28 AM, Dick Roth, KA1OZ wrote: > >> This is a very plain vanilla setup. I'm using an iambic paddle >> plugged into the paddle input and my straight key into the key input. >> Other than my KUSB connection between my rig and my laptop, which runs >> Vista, there is no other connection. And with the K3 in TX Test, >> there is no RF possibly running around the shack. >> >> I also have a plain vanilla setup of HRD...out of the box, you might >> say. I do know that without changing HRD's setup, I can cure the >> problem by going back to 3.30. It would appear that something in 3.41 >> has done the changing! >> >> Thanks for your input, Wayne, Len and the rest of the crew. >> >> >> Wayne Burdick wrote: >>> I'm not observing any keying problems, either. How are you keying the >>> rig? How is HRD set up? I'm not an expert with HRD; is there a way to >>> reset it to defaults to see if it could be a configuration issue? >>> Tnx >>> Wayne, >>> N6KR >>> ---- >>> http://www.elecraft.com >>> On Oct 8, 2009, at 7:00 PM, "Dick Roth, KA1OZ" <[email protected]> >>> wrote: >>>> Len, K3LJ wrote: >>>>> Dick, I tried it with my K3 #892 with no problems during TX Test. I am >>>>> running the latest Beta version of HRD. I have no problems using >>>>> HRD to do >>>>> CW or using the built in keyer in the K3. The mistakes that I make >>>>> using the >>>>> keyer are mine but nothing out of the ordinary other than that. >>>>> >>>>> Len, K3LJ >>>>> >>>>> >>>>> >>>>> Dick Roth KA1OZ wrote: >>>>>> Greetings-- >>>>>> >>>>>> I discovered tonight, having downloaded and installed 3.41 a few >>>>>> nights >>>>>> ago, that when connected to HRD, my K3, #859, has problems with the >>>>>> keying circuit, regardless if I'm using my paddle or my straight key. >>>>>> >>>>>> While in TX Test mode, when connected to HRD, dits and dahs become >>>>>> "spasmodic" with dahs occasionally elongated or cut off short. >>>>>> The dits >>>>>> will occasionally "miss"...not be there when expected. >>>>>> >>>>>> When disconnected from HRD, normal operation resumes. Now, I only >>>>>> tried >>>>>> this on TX Test and not into the air or dummy load. >>>>>> >>>>>> When I reverted back to 3.30, the problem vanished...ceased to exist, >>>>>> connected to HRD or not. >>>>>> >>>>>> Has anyone else discovered this? >>>>>> >>>>>>> >>>>> [snip] > >>>>> >>>> >>>> I'm running HRD 4.1 Build 2312. I should add that the radio is as it >>>> was when I put it together. I have not made any mods. I don't know if >>>> this is pertinent or not. >>>> >>>> -- >>>> 73, >>>> Dick ka1oz >>>> Middleborough, MA >>>> >>>> Radio: Elecraft K3/100(Kit) SN 859 >>>> Antenna: Titan-DX >>>> ______________________________________________________________ >>>> Elecraft mailing list >>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>> Help: http://mailman.qth.net/mmfaq.htm >>>> Post: mailto:[email protected] >>>> >>>> This list hosted by: http://www.qsl.net >>>> Please help support this email list: http://www.qsl.net/donate.html >> >> >> -- >> 73, >> Dick ka1oz >> Middleborough, MA >> >> Radio: Elecraft K3/100(Kit) SN 859 >> Antenna: Titan-DX > >
4.1 Build 2312 I'm using a KUSB from Elecraft. I re-installed 3.41 to see whether there had been a problem with the first time I installed it, but the same symptoms are there. I can't even send 8 dits (error) without a skipped dit! It makes it impossible to send morse. When I try the straight key, it is hit and miss whether I transmit or not with each character. I just re-installed 3.30 and all is FB again! -- 73, Dick ka1oz Middleborough, MA Radio: Elecraft K3/100(Kit) SN 859 Antenna: Titan-DX ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
