Hello, I wanted to download 3.97 but I couldn´t get it.
K3 utility worked but in the Available columns appears only the versions I already have: MCU 03.79 FPF 01.08 DSP1 02.54 DSP2 02.54 DVR 01.03 Any Idea I am not getting the latest versions? Thanks, Jorge CX6VM K3 #4077 -----Mensaje original----- De: [email protected] [mailto:[email protected]] En nombre de Wayne Burdick Enviado el: Martes, 18 de Mayo de 2010 04:06 p.m. Para: Elecraft Reflector; [email protected]; [email protected] Asunto: [Elecraft] K3 Firmware Rev. 3.97: new DSP NB algorithm, improved TX INHibit, accurate S-meter w/AGC off, etc. K3 beta-test firmware revision 3.97 (with DSP rev. 2.58) is now available. This revision has several significant improvements; see release notes below. (Note that "QRQ" mode -- enhanced high-speed CW -- will be in the next release.) Please send any questions to [email protected]. For instructions on how to load beta firmware, see: http://www.elecraft.com/K3/k3_software.htm 73, Wayne N6KR * * * MCU 3.97 / DSP 2.58, 5-9-2010 * TX INHIBIT IMPROVEMENT: If TX INH is active (see CONFIG:TX INH), voice monitor and CW/DATA tones are disabled, giving the operator audible feedback about inhibited status to supplement the flashing TX icon. * DSP NOISE BLANKER IMPROVED: A new algorithm has been added that makes the DSP NB more effective on some types of noise. Odd-numbered DSP NB levels (t1-1, t1-3, t1-5, etc.) apply the new algorithm, while even-numbered levels use the original. To avoid unwanted interaction between the NB and on-air signals, always use the lowest effective setting. * CW KEYING ARTIFACT WITH AFX/DELAY ELIMINATED: The DELAY settings of AFX previously created a small audio artifact when listening to CW keying in the presence of background noise or signals. * AGC-OFF S-METER IMPROVEMENT: Turning AGC off no longer results in a drop in the S-meter reading. This was most noticeable in the presence of strong band noise. * K144XV S-METER NOW ACCURATE: The S-meter reading is now adjusted to account for RX gain when the K144XV is in use. * TX NOISE GATE IMPROVED: The voice transmit noise gate now uses a downward expander rather than simple gating. See TX GATE menu entry for further details. * MANUAL NOTCH: Pitch now defaults to 1000 rather than 2000 Hz. This starting point is a better compromise between CW and SSB. * ESSB ON/OFF COMMAND: The new ES control command can be used to turn ESSB on/off via a switch macro or from a software application. The K3 must also be in LSB or USB mode before ESSB ON takes effect. (See K3 Programmers Reference.) * BN REMOTE CONTROL COMMAND (BAND CHANGE): Previously this command was GET only, returning the present band number (00-24). It can now be used as a SET command to switch to the desired band. For example, BN00; switches to the last-used frequency on 160 m. Note: VFO B will also be restored to its last frequency used on the new band, except in the case where CONFIG:VFO IND is set to YES. ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
