On Monday 24 June 2019 14:01:33 Gene Heskett wrote: > On Monday 24 June 2019 11:29:44 Gene Heskett wrote: > > On Monday 24 June 2019 10:20:14 andy pugh wrote: > > > On Mon, 24 Jun 2019 at 15:16, Gene Heskett <[email protected]> > > > > wrote: > > > > dpkg-checkbuildeps fails here, no debian/control has been > > > > generated because configure takes a dump. > > > > > > It's a different configure. (you need to make sure you are in the > > > debian directory and running the debian configure) > > > And it needs to be configure --uspace (I think, it was hours ago > > > that I did it) > > > > I must have skipped ahead to doing it in the src dir, its working > > now after doing that. And apt is installing the list. 294 pkgs, > > 1.3GB. That will take a few yet. In fact, everything except where to > > get it is dust in the wind until section 3.2 where the real work > > starts. > > > > Still had to add about 6 dependencies before configure would run to > > completion, but cd ..;dpkg-buildpackage is running now. > > > > Many thanks, following the web page its too easy to get out of > > sequence. > > > > Humm, just stopped at building rs274ngc. Restarted > > dpkg-buildpackage, which starts from square one. And it shouldn't be > > hot, the -j didn't have an argument. So we'll see in another hour > > or so. > > > > Until its done, bye for now, Thank you Andy. > > And I see whats stopping it, same place, out of virtual memory, and > despite one of the attached ssd's having a 10GB swap partition, its > not mounted! Doesn't show up except as 100 megs in htop, apparently in > the u-sd. > > fstab is blank, so is mounts output. I thought finding an assigning > swap was automatic. I'll see if I can dupe whats here in my fstab and > put it in the pi's fstab. > > I think it worked but the only place I can see it after a reboot is in > htop. But it must be working, it got past that particular file as it > is proceeding now, with htop showing its 75 megs into 9.7GB of swap, > and all 4 cores busier than that famous cat on a tin roof. Can I call > it progress? I would like to see a sensors output though to see how > hot the pi is getting. > > But getting close to the end I've a boatload of warnings I've not seen > before: > dh_makeshlibs > objdump: > debian/linuxcnc-uspace/usr/lib/python2.7/dist-packages/qtvcp/designer/ >x86_64/qt5.9/libpyqt5_py2.so.tar.gz: File format not recognized > dh_installdeb > cat debian/linuxcnc-uspace/DEBIAN/shlibs debian/shlibs.pre > > debian/shlibs.local > dh_shlibdeps -l debian/linuxcnc-uspace/usr/lib > dpkg-shlibdeps: warning: debian/linuxcnc-uspace/usr/bin/schedrmt > contains an unresolvable reference to symbol > __aeabi_atexit@CXXABI_ARM_1.3.3: it's probably a plugin > dpkg-shlibdeps: warning: debian/linuxcnc-uspace/usr/bin/milltask > contains an unresolvable reference to symbol > __aeabi_atexit@CXXABI_ARM_1.3.3: it's probably a plugin > dpkg-shlibdeps: warning: debian/linuxcnc-uspace/usr/bin/rs274 contains > an unresolvable reference to symbol __aeabi_atexit@CXXABI_ARM_1.3.3: > it's probably a plugin > dpkg-shlibdeps: warning: debian/linuxcnc-uspace/usr/bin/rtapi_app > contains an unresolvable reference to symbol > __aeabi_atexit@CXXABI_ARM_1.3.3: it's probably a plugin > dpkg-shlibdeps: warning: symbol _Z11PROGRAM_ENDv used by > debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the > libraries > dpkg-shlibdeps: warning: symbol _Z21ENABLE_SPEED_OVERRIDEi used by > debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the > libraries > dpkg-shlibdeps: warning: symbol _Z13SET_FEED_MODEii used by > debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the > libraries > dpkg-shlibdeps: warning: symbol _task used by > debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the > libraries > dpkg-shlibdeps: warning: symbol _Z25GET_EXTERNAL_ANALOG_INPUTid used > by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the > libraries > dpkg-shlibdeps: warning: symbol _Z13SELECT_POCKETii used by > debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the > libraries > dpkg-shlibdeps: warning: symbol _Z23GET_EXTERNAL_POSITION_Yv used by > debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the > libraries > dpkg-shlibdeps: warning: symbol _Z28WAIT_SPINDLE_ORIENT_COMPLETEid > used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of > the libraries > dpkg-shlibdeps: warning: symbol _parameter_file_name used by > debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the > libraries > dpkg-shlibdeps: warning: symbol _Z24GET_EXTERNAL_QUEUE_EMPTYv used by > debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the > libraries > dpkg-shlibdeps: warning: 135 other similar warnings have been skipped > (use -v to see them all) > dpkg-shlibdeps: warning: can't extract name and version from library > name 'libtk8.6.so' > dpkg-shlibdeps: warning: symbol _Z11PROGRAM_ENDv used by > debian/linuxcnc-uspace/usr/lib/libcanterp.so.0 found in none of the > libraries > > But the packages (debs) are built. > > drwxr-xr-x 2 pi pi 4096 Jun 18 15:25 kernels-rt > -rw-r--r-- 1 pi pi 19779 Jun 24 13:16 > linuxcnc_2.9.0~pre0_armhf.buildinfo > -rw-r--r-- 1 pi pi 2916 Jun 24 13:16 > linuxcnc_2.9.0~pre0_armhf.changes > drwxr-xr-x 18 pi pi 4096 Jun 24 13:10 linuxcnc-dev > -rw-r--r-- 1 pi pi 13138258 Jun 24 13:15 > linuxcnc-doc-en_2.9.0~pre0_all.deb > -rw-r--r-- 1 pi pi 11636962 Jun 24 13:15 > linuxcnc-doc-es_2.9.0~pre0_all.deb > -rw-r--r-- 1 pi pi 6157132 Jun 24 13:15 > linuxcnc-doc-fr_2.9.0~pre0_all.deb > drwxr-xr-x 18 pi pi 4096 Jun 18 10:14 linuxcnc-jessie-dev > -rw-r--r-- 1 pi pi 6589218 Jun 24 13:15 > linuxcnc-uspace_2.9.0~pre0_armhf.deb > -rw-r--r-- 1 pi pi 9211096 Jun 24 13:15 > linuxcnc-uspace-dbgsym_2.9.0~pre0_armhf.deb > -rw-r--r-- 1 pi pi 741024 Jun 24 13:15 > linuxcnc-uspace-dev_2.9.0~pre0_armhf.deb > > Thanks Andy. > > Installed, but had to install some more stuff with an > sudo apt --fix-broken install, and: > latency-test --base-thread shows a max servo jitter of 29 u-secs, > which will run a 7i90 running that lathe just fine. Now to get > amanda-common and amanda-client installed and enabled then restore my > linuxcnc configs and nc_files directories from jessie. And that should > put me back in business! (as if there was any business but my hobby > stuffs) Setting up amanda to do everything can be involved however. > > Cheers, Gene Heskett
Turned out I had to get creative with dd & gzip and a tar or 2, but I got it recovered and everything is working. Latency at 28 microseconds for the servo thread, is better than the 70 microseconds I was getting out of a 4.4.4-rt kernel and the jessie install. So I am a happy camper. Very happy. Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) If we desire respect for the law, we must first make the law respectable. - Louis D. Brandeis Genes Web page <http://geneslinuxbox.net:6309/gene> _______________________________________________ Emc-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-developers
