My higher horns came from Millitech. Leslie Bai wrote:
> EMCO has no horn over 40GHz. > > --- "WOODS, RICHARD" <wo...@sensormatic.com> wrote: > > > > Try EMCO for horns and MITEQ for preamps. > > > > ---------- > > From: Leslie Bai [SMTP:leslie_...@yahoo.com] > > Sent: Thursday, August 12, 1999 1:15 PM > > To: 'emc-p...@majordomo.ieee.org' > > Subject: Horn antennas, pre-amplifier, and return > > loss measurement > > > > > > Hi, Folks, > > > > Is there anyone can direct me to some sources > > of horn antennas & preamplifiers. > > > > What I need are sets of horn antenna for spurious > > emissions testing to meet FCC Part 101. > > > > 1 to 18GHz, > > 18 to 26.5GHz, 26.5 to 40GHz, or 18 to 40GHz > > instead, > > 40 to 60GHz, 50 to 75GHz, or 40 to 75GHz instead, > > 75 to 110GHz, 110 to 170GHz, or 75 to 170GHz > > instead. > > > > Due to the significant space loss over 110GHz, I > > guess > > I also need a set of preamplifier from 110 to > > 170GHz. > > > > I am also studying on return loss measurement > > methodologies to meet ETSI requirement for > > radios RF port. Since NAMAS calibration of > > network analyzer may cost thousands bucks, > > I am wondering if I could achieve a good result > > (in terms of accuracy and uncertainty) using > > spectrum analyser and waveguide coupler. > > If anyone by any chance has an ready error model > > of the test setup using spectrum analyzer and > > waveguide coupler, I appreciate you could share > > with me to short my research path. > > > > Thanks in advance. > > > > Leslie Bai > > Senior Compliance Engineer > > Compliance Quality Manager > > Digital Microwave Corporation > > 170 Rose Orchard Way > > San Jose, CA 95134 > > Tel: (408)-944-1754 > > > > > > _________________________________________________________ > > Do You Yahoo!? > > Get your free @yahoo.com address at > > http://mail.yahoo.com > > > > > > --------- > > This message is coming from the emc-pstc discussion > > list. > > To cancel your subscription, send mail to > > majord...@ieee.org > > with the single line: "unsubscribe emc-pstc" > > (without the > > quotes). For help, send mail to > > ed.pr...@cubic.com, > > jim_bac...@monarch.com, ri...@sdd.hp.com, or > > roger.volgst...@compaq.com (the list > > administrators). > > > > > > --------- > > This message is coming from the emc-pstc discussion > > list. > > To cancel your subscription, send mail to > > majord...@ieee.org > > with the single line: "unsubscribe emc-pstc" > > (without the > > quotes). For help, send mail to ed.pr...@cubic.com, > > jim_bac...@monarch.com, ri...@sdd.hp.com, or > > roger.volgst...@compaq.com (the list > > administrators). > > > > > > > > _________________________________________________________ > Do You Yahoo!? > Bid and sell for free at http://auctions.yahoo.com > > --------- > This message is coming from the emc-pstc discussion list. > To cancel your subscription, send mail to majord...@ieee.org > with the single line: "unsubscribe emc-pstc" (without the > quotes). For help, send mail to ed.pr...@cubic.com, > jim_bac...@monarch.com, ri...@sdd.hp.com, or > roger.volgst...@compaq.com (the list administrators). -- Jon D. Curtis, PE Curtis-Straus LLC j...@curtis-straus.com Laboratory for EMC, Safety, NEBS, SEMI-S2 and Telecom 527 Great Road voice (978) 486-8880 Littleton, MA 01460 fax (978) 486-8828 http://www.curtis-straus.com --------- This message is coming from the emc-pstc discussion list. To cancel your subscription, send mail to majord...@ieee.org with the single line: "unsubscribe emc-pstc" (without the quotes). For help, send mail to ed.pr...@cubic.com, jim_bac...@monarch.com, ri...@sdd.hp.com, or roger.volgst...@compaq.com (the list administrators).
