The EMC-30 is spec'd for 75% relative humidity -- and they mean it. If you operate the instrument in RH above this, you will loose control, i.e., seems to be some shorting between front panel control functions.
> ---------- > From: Ken Javor[SMTP:[email protected]] > Reply To: Ken Javor > Sent: Wednesday, May 23, 2001 2:59 PM > To: Wolak, Marvin; EMC-PSTC Newsgroup (E-mail) > Subject: Re: CISPR Compliant Spectrum analyzer/receiver > > > I would look at the Electrometrics EMC-30 and the Carnel NM 17/27. I > think > these have built-in quasi-peak detection, but I'm not sure. Both of these > machines have tunable front ends (built-in preselection). > > ---------- > >From: "Wolak, Marvin" <[email protected]> > >To: "EMC-PSTC Newsgroup (E-mail)" <[email protected]> > >Subject: CISPR Compliant Spectrum analyzer/receiver > >Date: Wed, May 23, 2001, 11:11 AM > > > > > > > I need to rent a CISPR 16 compliant spectrum analyzer/receiver over the > > frequency range 0.15 - 30 MHz. > > > > Any suggestions? > > > > I'm familiar with the good ol' HP 8566 / 8568 (Do I need the preselector > > with them for CISPR 16 compliance?), and the R&S ESI. > > > > What else may be out there available in the rental shops? > > > > Thanks, > > > > Marvin Wolak > > Marconi Networks > > > > ------------------------------------------- > > This message is from the IEEE EMC Society Product Safety > > Technical Committee emc-pstc discussion list. > > > > Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ > > > > To cancel your subscription, send mail to: > > [email protected] > > with the single line: > > unsubscribe emc-pstc > > > > For help, send mail to the list administrators: > > Michael Garretson: [email protected] > > Dave Heald [email protected] > > > > For policy questions, send mail to: > > Richard Nute: [email protected] > > Jim Bacher: [email protected] > > > > All emc-pstc postings are archived and searchable on the web at: > > http://www.rcic.com/ click on "Virtual Conference Hall," > > > > ------------------------------------------- > This message is from the IEEE EMC Society Product Safety > Technical Committee emc-pstc discussion list. > > Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ > > To cancel your subscription, send mail to: > [email protected] > with the single line: > unsubscribe emc-pstc > > For help, send mail to the list administrators: > Michael Garretson: [email protected] > Dave Heald [email protected] > > For policy questions, send mail to: > Richard Nute: [email protected] > Jim Bacher: [email protected] > > All emc-pstc postings are archived and searchable on the web at: > http://www.rcic.com/ click on "Virtual Conference Hall," > ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Michael Garretson: [email protected] Dave Heald [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.rcic.com/ click on "Virtual Conference Hall,"
