As can we. ITS has been approved by Gosstandart to issue the GOST-R mark required for Russia.
Bob Martin, P.E., N.C.E. Intertek Testing Services, NA 978-263-2662 fax 978-263-7086 www.etlsemko.com -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Wednesday, January 10, 2001 7:59 PM To: 'Courtland Thomas'; Gorodetsky, Vitaly Cc: emcpost Subject: RE: Approvals for Russia Courtland, you can reach me on my cell at 403-615-4672. We can help out here. Regards, Regan Arndt TUV Rheinland of North America, Inc. Thanks Vitaly. "Gorodetsky, Vitaly" <[email protected]>@ieee.org on 01/10/2001 10:44:14 AM Please respond to "Gorodetsky, Vitaly" <[email protected]> Sent by: [email protected] To: "'Courtland Thomas'" <[email protected]>, emcpost <[email protected]> cc: Subject: RE: Approvals for Russia Thomas - There are many additional requirements. First, your product has to be approved for GOST-R mark; telecom homologation has to be evaluated by a Russian Telecom Certification Center. In some cases, additional, what Russians call "hygienic" (ergonomic), requirements are applicable. Good news is that Russia is a member of IEC and that they accept CB scheme Reports and, in many instances, EMC Reports for CE mark (FCC is not sufficient). Also, to my knowledge, they require annual follow-up inspections. For details, contact TUV Rheinland, UL, ITS (and few others) which have been accredited to do Russian ITE certification. Vitaly Gorodetsky Compliance Engineer Direct: (818) 678-3840 Canoga Perkins Corp. Main: (818) 718-6300 20600 Prairie Street FAX: (818) 678-3740 Chatsworth, CA 91311-6008 e-mail: [email protected] <mailto:[email protected]> The suitability of this information for making decision is solely with the reader -----Original Message----- From: Courtland Thomas [SMTP:[email protected]] Sent: Wednesday, January 10, 2001 11:07 AM To: emcpost Subject: Approvals for Russia Hello Group, I am interested in knowing if there are any special types of approvals required for Russia concerning IT equipment. We typically test our products to, and label them with CE, FCC Part 15, UL and where required BABT. We also self verify to CTR's 12,13 ad 14 when applicable. Is there anything else required. Thanks, Courtland Thomas Patton Electronics ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: [email protected] Michael Garretson: [email protected] For policy questions, send mail to: Richard Nute: [email protected] ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: [email protected] Michael Garretson: [email protected] For policy questions, send mail to: Richard Nute: [email protected] ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: [email protected] Michael Garretson: [email protected] For policy questions, send mail to: Richard Nute: [email protected] ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: [email protected] Michael Garretson: [email protected] For policy questions, send mail to: Richard Nute: [email protected]
