Thanks all for the help. When I wrote my original question I realized later I had the incorrect standard, though the limits are identical. I have actually applied the generic standards to this unit.
Ian may be on to something though. This is a Hydraulic pump that is driven by the motor. EN 55014-1 maybe a better standard to test to for this device. My question now is can this standard be applied to industrial equipment? Thanks, Josh Gordon,Ian wrote: > Josh > Although not referred to in EN61326 can you apply EN55014-1 to your product? > This provides for assessment of discontinuous interference. > Scope of EN 55014-1: > > ELECTROMAGNETIC COMPATIBILITY - > REQUIREMENTS FOR HOUSEHOLD APPLIANCES, > ELECTRIC TOOLS AND SIMILAR APPARATUS - > Part 1: Emission > 1 Scope > 1.1 This standard applies to the conduction and the radiation of > radio-frequency disturbances > from appliances whose main functions are performed by motors and switching > or regulating devices, > unless the r.f. energy is intentionally generated or intended for > illumination. > It includes such equipment as: household electrical appliances, electric > tools, regulating controls using > semiconductor devices, motor-driven electro-medical apparatus, > !electric/electronic toys", > automatic dispensing machines as well as cine or slide projectors. > © BSI 14 July 2003 > > Furthermore, does the margin of 1-2dB over the limit line to which you refer > to take into consideration the measurement uncertainties associated with the > test? If not then the following may apply (taken from section 4.6.1 of UKAS > document LAB34): > > "The measured result is above (below) the > specification limit by a margin less than the > measurement uncertainty; it is therefore not > possible to state compliance based on the > 95% level of confidence. However, the result > indicates that compliance (non-compliance) > is more probable than non-compliance > (compliance) with the specification limit." > > > > Ian Gordon > >>-----Original Message----- >>From: Josh Wiseman [mailto:[email protected]] >>Sent: 21 March 2005 16:42 >>To: EMC-PSTC >>Subject: EN 61326-1 question >> >> >>All, >> >>I have been testing a clients unit that uses a universal AC >>motor. The >>unit is intended to operate for 5-10 minutes and be idle for >>30 minutes >>up to several hours before it is operated again. >> >>The unit currently will not meet the Class A radiated emissions limit, >>the QP value is 1-2 dB over the limit around 45 MHz. Since >>this unit is >>meant for industrial environments I am curious if there is something >>that would allow this emission based on the duration of use. >> >>Thanks in advance for the help. >>Josh >>-- >>Josh Wiseman >>Owner, A2Z Compliance >>CE Lab Manager, L F Research >> > > > *********************************************************************** > The information contained in this email and any attachments may be confidential and is provided solely for the use of the intended recipient(s). If you are not the intended recipient, you are hereby notified that any disclosure, distribution, or use of this e-mail, its attachments or any information contained therein is unauthorised and prohibited. If you have received this in error, please contact the sender immediately and delete this e-mail and any attachments. > > No responsibility is accepted for any virus or defect that might arise from opening this e-mail or attachments, whether or not it has been checked by anti-virus software. > > ---------------------------------------------------------------- > This message is from the IEEE Product Safety Engineering Society > emc-pstc discussion list. Website: http://www.ieee-pses.org/ > > To post a message to the list, send your e-mail to [email protected] > > Instructions: http://listserv.ieee.org/listserv/request/user-guide.html > > List rules: http://www.ieee-pses.org/listrules.html > > For help, send mail to the list administrators: > > Scott Douglas [email protected] > Mike Cantwell [email protected] > > For policy questions, send mail to: > > Richard Nute: [email protected] > Jim Bacher: [email protected] > > All emc-pstc postings are archived and searchable on the web at: > > http://www.ieeecommunities.org/emc-pstc > -- Josh Wiseman Owner, A2Z Compliance CE Lab Manager, L F Research This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. Website: http://www.ieee-pses.org/ To post a message to the list, send your e-mail to [email protected] Instructions: http://listserv.ieee.org/listserv/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas [email protected] Mike Cantwell [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc
