Denis Lithium cells and batteries themselves have the ID UN3090 and are subject to Packing Instruction 903. Lithium cells and batteries contained in equipment have the ID UN3091 and are subject to Packing Instruction 912. Lithium cells and batteries packed with equipment also have the ID UN3091 and are subject to Packing Instruction 918. PIs 912 and 918 both require that the requirements of 903 are met. PI 903 requires that the cells or batteries are tested according to UN Document ST/SG/AC.10/11. Unfortunately I do not have that document, but I guess it contains the tests that you refer to as T1 - T8. The document is available at a cost of $10. Consequently, your first task has to be to obtain test results for the battery asembly, otherwise none of the packing instructions can be met. Once that requirement has been met, the rest of the PIs are fairly straightforward, dealing with separation, prevention of short circuits, and prevention of discharge during shipment. That latter requirement is to meet a common requirement that no cell should be discharged to a potential of the lower of either 2V or 2/3 of the undischarged voltage of the cell. Cells with a voltage below these levels are forbidden from transport. The mass of Lithium in your battery is well below any limits required. For further information, consult the IATA Dangerous Goods Regulations. I hope this helps. Best regards
Neil R. Barker CEng MIET HonFSEE MIEEE Manager Quality Engineering e2v technologies (uk) ltd 106 Waterhouse Lane Chelmsford Essex CM1 2QU UK Tel: (+44) 1245 453616 Fax: (+44) 1245 453571 Mob: (+44) 7801 723735 P Please consider the environment before printing this email. From: Denis Ryskamp [mailto:[email protected]] Sent: 11 March 2008 19:08 To: [email protected] Subject: Lithium Ion battery shipping requirements This is a little out of my expertise, need help---What would the testing and packaging requirements be to ship international and US, a battery assembly of 2 cells with ELC of 2.7g, with the battery installed within the product? Note: Found that the battery assembly has not been tested to UN T1-T8. Regards, Denis Ryskamp Environmental Compliance Manager Trimble Dayton 5475 Kellenburger Road Dayton, Ohio 45424 *: 01-937-245-5539 *: [email protected] _____ From: [email protected] [mailto:[email protected]] On Behalf Of Elliott Mac-FME001 Sent: Tuesday, March 11, 2008 11:48 AM To: [email protected] Subject: ANSI C63.4 Site Requirements Above 1 GHz Hello Group We have heard through the grapevine that ANSI C63.4 will be following CISPR 16 for site validation above 1 GHz. Does anyone out there have any additional information regarding whether or not free-space OATS will be required per ANSI C63.4 in the near future? Imagine it will if the site validation criteria follows CISPR 16. Does anyone know approximate timeframes for this if it is in Committee so we can start making plans to enclose our OATS? Best regards, Mac - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. Website: http://www.ieee-pses.org/ To post a message to the list, send your e-mail to [email protected] Instructions: http://listserv.ieee.org/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas [email protected] Mike Cantwell [email protected] For policy questions, send mail to: Jim Bacher: [email protected] David Heald: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. Website: http://www.ieee-pses.org/ To post a message to the list, send your e-mail to [email protected] Instructions: http://listserv.ieee.org/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas [email protected] Mike Cantwell [email protected] For policy questions, send mail to: Jim Bacher: [email protected] David Heald: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc Sent by E2V TECHNOLOGIES PLC or a member of the E2V group of companies. A company registered in England and Wales. Company number 04439718. Registered address 106 Waterhouse Lane, Chelmsford, Essex, CM1 2QU, UK. - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. Website: http://www.ieee-pses.org/ To post a message to the list, send your e-mail to [email protected] Instructions: http://listserv.ieee.org/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas [email protected] Mike Cantwell [email protected] For policy questions, send mail to: Jim Bacher: [email protected] David Heald: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc
