Reference IEC/EN 61010-1 2nd Ed. Safety Standard. Our product is considered Laboratory Equipment.
The | and O symbols are on our Mains Supply Switch/Breaker which is also our Disconnect Device, but engineering wants to use additional switch/breakers (functional purpose) to power on/off different sections of the product. The switch/breakers they want to use are breaking AC Mains to sections of the product and have the | and O symbols printed right on the switches. It has always been my understanding that the | and O symbols can only be used on the Disconnect Device which cuts AC mains to the entire product. Can the | and O symbol also be used on other AC Main switch/breakers that cut AC Mains Supply power to only sections within the product but not the entire product? In our case, these additional switch/breaker cut AC mains to circuits but there are other circuits in the same section that are still powered up. The purpose of these additional switches are to power down sections or devices for power savings at night when some sections of the product need to stay on 24/7. One last detail; all the switch/breaker including the Disconnect Device switch are all physically mounted on the same panel right next to each other, so I am concern with the proper identification of the Disconnect Device switch. Other than the | and O symbol, are there other ways to identify the Disconnect Device switch? The manufacturer of the switch/breakers will not make it without the | and O symbols without loosing its VDE certification. I’ve been telling engineering that the | and O symbols can only be used on the Disconnect Device. Am I wrong? The standard says, “Symbols | and O shall not be used for switches other than the power supply switch.”, however, section 5.1.6 says, “If the power supply switch .. is used as the disconnecting device…”, implies that a power supply switch does not have to be the Disconnect Device. Please help clarify this circular logic for me. The Other Brian PS: Here is the entire section 5.1.6 to use as a referrence: 5.1.6 Switches and circuit-breakers If the power supply switch or circuit-breaker is used as the disconnecting device, the on-position or the off-position shall be clearly marked. Symbols 9 and 10 of table 1 can, in some cases, also be suitable as the device identification (see 6.11.2.5). A lamp alone is not considered to be a satisfactory marking. Symbols 9 and 10 shall not be used for switches other than the power supply switch. 6.11.3.1 Switches and circuit-breakers An equipment switch or circuit-breaker employed as a disconnecting device shall meet the relevant requirements of IEC 60947-1 and IEC 60947-3 and be suitable for the application. If a switch or a circuit-breaker is used as a disconnecting device, it shall be marked to indicate this function. If there is only one device – one switch or one circuit-breaker – symbols 9 and 10 of table 1 are sufficient. A switch shall not be incorporated in a MAINS supply cord. A switch or circuit-breaker shall not interrupt a protective earth conductor. A switch or circuit-breaker with contacts for disconnecting and other contacts for other purposes shall conform to the requirements of 6.6 and 6.7 for separation between circuits. Conformity is checked by inspection. _________________________ LECO Corporation Notice: This communication may contain confidential information intended for the named recipient(s) only. If you received this by mistake, please destroy it and notify us of the error. Thank you. - This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at http://www.ieeecommunities.org/emc-pstc Graphics (in well-used formats), large files, etc. can be posted to that URL. Website: http://www.ieee-pses.org/ Instructions: http://listserv.ieee.org/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher <[email protected]> David Heald <[email protected]>
