Hey Ken – thanks! The note in ANSIC63 says that the preselector is required to increase the dynamic range of the instrument. Is it simply a noise floor issue – but then why the <20Hz specificity?
Best Regards Charles Grasso Compliance Engineer Echostar Communications (w) 303-706-5467 (c) 303-204-2974 (t) [email protected] (e) [email protected] (e2) [email protected] From: Ken Wyatt [mailto:[email protected]] Sent: Thursday, October 22, 2015 1:23 PM To: [email protected] Subject: Re: [PSES] Preselector requirement in ANSIC63.4 -low PRF I would think that if the measurements were taken in a chamber and the product emissions were characterized and amplitudes known and the analyzer was a good quality one, justification could be made to eliminate the preselector. I suspect the requirement was established during the days we all were using OATS. Kenneth Wyatt Woodland Park, CO Sent from my iPhone. On Oct 22, 2015, at 12:58 PM, Sundstrom, Mike <[email protected]<mailto:[email protected]>> wrote: So the SA is not in overload, which could give a wrong amplitude otherwise. Thanks, Michael Sundstrom Garmin Compliance Engineer 2-2606 (913) 440-1540 KB5UKT “Never give up on a dream just because of the time it will take to accomplish it. The time will pass anyway.” Earl Nightingale From: Grasso, Charles [mailto:[email protected]] Sent: Thursday, October 22, 2015 1:53 PM To: [email protected]<mailto:[email protected]> Subject: [PSES] Preselector requirement in ANSIC63.4 -low PRF Hell all, ANSI C63 *requires* the use of a preselector on an SA when making QP measurements of a signal with a low repetition rate (lower than 20Hz or less). Does anyone know why? Best Regards Charles Grasso Compliance Engineer Echostar Communications (w) 303-706-5467 (c) 303-204-2974 (t) [email protected]<mailto:[email protected]> (e) [email protected]<mailto:[email protected]> (e2) [email protected]<mailto:[email protected]> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]<mailto:[email protected]>> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe)<http://www.ieee-pses.org/list.html> List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]<mailto:[email protected]>> Mike Cantwell <[email protected]<mailto:[email protected]>> For policy questions, send mail to: Jim Bacher <[email protected]<mailto:[email protected]>> David Heald <[email protected]<mailto:[email protected]>> ________________________________ CONFIDENTIALITY NOTICE: This email and any attachments are for the sole use of the intended recipient(s) and contain information that may be confidential and/or legally privileged. If you have received this email in error, please notify the sender by reply email and delete the message. Any disclosure, copying, distribution or use of this communication (including attachments) by someone other than the intended recipient is prohibited. Thank you. - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]<mailto:[email protected]>> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe)<http://www.ieee-pses.org/list.html> List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]<mailto:[email protected]>> Mike Cantwell <[email protected]<mailto:[email protected]>> For policy questions, send mail to: Jim Bacher <[email protected]<mailto:[email protected]>> David Heald <[email protected]<mailto:[email protected]>> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]<mailto:[email protected]>> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe)<http://www.ieee-pses.org/list.html> List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]<mailto:[email protected]>> Mike Cantwell <[email protected]<mailto:[email protected]>> For policy questions, send mail to: Jim Bacher <[email protected]<mailto:[email protected]>> David Heald <[email protected]<mailto:[email protected]>> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher: <[email protected]> David Heald: <[email protected]>
